Image generation is currently failing on builbots due to the following
error:
WARNING: Image file [...] mt7620-ex2700-squashfs-factory.bin is too big
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Many Atom-based embedded/industrial x86 boards can't run 64bit operating
systems due to either processor or board firmware limitations, but they
have modern interfaces (PCIe) or have modern Intel gigabit controllers
onboard. With the current default package selection for x86 Generic
target their network won't work.
Add the modern gigabit network modules needed or most likely going to be
used as add-in cards, similar to what is the list on x86_64 target.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit bb27cde2579b0273c464e5ccd3dda7d14e84fd23)
Image generations is currently failing on builbots due to the following
errors:
mkfwimage -B XS2 -v XS2 [...] ath25-ubnt2-squashfs-sysupgrade.bin
ERROR: Failed creating firmware layout description - error code: -2
mkfwimage -B XS5 -v XS5 [...] ath25-ubnt5-squashfs-sysupgrade.bin
ERROR: Failed creating firmware layout description - error code: -2
That cryptic -2 error simply means, that kernel+rootfs doesn't fit into
the firmware partition.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In ath79, identifiers tplink_tl-wdr3600 and tplink_tl-wdr4300 have
been used while most other TP-Link devices include the revision.
Although there actually is only one major revision of these
devices, they bear the revision on their bottom (v1.x). TP-Link
also refers to the devices as V1 on its web page.
This patch thus adds -v1 to both so it is more consistent
with other devices and with what you would expect from reading
the on-device sticker and the support pages.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It was reported in FS#2385, that Carambola2 doesn't currently have
working watchdog so fix it by adding watchdog node.
Ref: FS#2385
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 0893f28e19afbd9d4081f59df10631d6ef02e0d7)
While flashing lots of RB2011 devices, I noticed that
some of them refused to boot properly, failing over the NAND parameters.
Checking in detail shows that some device seem to use another NAND flash
which only support standard 2048-byte pages, without 512-byte subpage support.
This commit disables usage of these small subpage completely.
Advantages:
- Both NAND's with(out) subpage support are working now
- The nand speed increases a bit (measured roughly 1%) in typical usecases
Disadvantages:
- The maximum storage capacity decreases by ~0.2%
as small changes can consume a full page (2048 bytes) now.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
This is already included in newer upstream. Needed to build BPF programs
using the MIPS kernel include files.
Without this patch, clang fails with "#error Use a Linux compiler or
give up." in sgidefs.h when building BPF programs.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
(cherry-picked from commit 7d96c301d6afc9f360c26b404e435e8e03c1e207)
After commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage")
XZ compression of zImage was enabled. This change exposed a problem with
the HiveAP-330 images, which was fixed by foregoing the compression on
the kernel altogether with commit 98089bb8ba8
("mpc85xx: Use uncompressed kernel on the HiveAP-330").
This patch adds back the gzip compression of the kernel image by
utilizing the generic OpenWRT uImage method instead of relying on
the PowerPC bootwrapper script that did it previously.
Compile-tested: p1020/hiveap-330
Tested-by: Chris Blake <chrisrblake93@gmail.com> [run-tested]
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[filled in even more text]
While moving common used parts to dtsi files, the was disabled by
default but not enabled for all boards using the STP.
Fixes: f519fea4c6 ("lantiq: kernel 4.14: cleanup dts files")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Apply the same approach as in commit 3b53d6fdbc ("ar71xx: fix pci irq
init on kernel 4.14") to fix IRQ initialization for ath79-based chipsets
on rb4xx.
Ref: PR#2182
Acked-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: W. Michael Petullo <mike@flyn.org>
[commit ref fix]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8c7d6c47a7893db689e50e1917479ad07a96547a)
When the non-generic espressobin targets were added these board checks
were not updated. One side effect of this is that config is not saved
during an upgrade of -emmc,-v7, or -v7-emmc devices.
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
(cherry picked from commit 95c1dc5e8678a1fd87234a4d77c8c6643703023c)
When targets for multiple ESPRESSObin devices were added, not all
files were updated which means any ESPRESSObin version beside generic
won't have proper networking, sysupgrade and uboot-env. This patch
fixes the issue.
* fixup network detection
* fixup uboot-env
* fixup platform.sh for sysupgrade
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(cherry picked from commit bc47285cb3c0125424e628521f905f1f0d7b4cef)
Not all versions of ESPRESSObin require SD card, but can
be booted from the internal emmc flash (mmc dev 1) instead.
Add a simple check in the bootscript to see which mmc device
is detected and boot from it using mmcdev variable.
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
(cherry picked from commit 008b41b9b0ddd4c5c877a769a85d27eb9c4e21a4)
This makes interrupt-based gpio-keys working.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 110daa16e44bb53941a18396ab6a7d9fdd1fa362)
An aquantia phy patch which dropped pause frame support was
missing when integrated LSDK-19.03 kernel patches into OpenWrt.
Without this patch, LS1043A 10G port would not work. So apply it.
Patch link
https://source.codeaurora.org/external/qoriq/qoriq-components/
linux/commit/?h=linux-4.14&id=66346b115818365cfaf99d292871b19f0a1d2850
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
"There are often transient line events when
the system is powered up and initialized and it
is often necessary for the gpio_chip driver to
clear any interrupt flags in hardware before
setting up the gpio chip, especially the
irqchip portions of it."
<http://lists.infradead.org/pipermail/openwrt-devel/2019-June/017630.html>
This patch adds a fix for the APM821XX's interrupt
controller to clear any bogus pending toggled
interrupts that happens on various APM821XX boards
on boot.
The patch also changes the debouce-interval from the
default 5ms debounce interval to 60ms all around.
The default setting caused on occasions that the button
state became stuck in a pressed state, even though the
button was released.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It seems that newer builds of OpenWRT have a gzip kernel
larger than 2MB~, which for some reason fails to boot on this board.
However, we have 8MB of kernel space and currently the uncompressed
kernel is 6.5MB~, so we have some space to grow until a better
solution is worked out.
Before:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 2315724 Bytes = 2.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Uncompressing Kernel Image ... Error: Bad gzipped data
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
ft_fixup_l2cache: FDT_ERR_NOTFOUND
After:
## Booting kernel from Legacy Image at ee840000 ...
Image Name: POWERPC OpenWrt Linux-4.19.53
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux Kernel Image (uncompressed)
Data Size: 6724584 Bytes = 6.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 02000000 ...
Image Name: OpenWrt fake ramdisk
Created: 2019-06-22 11:17:48 UTC
Image Type: PowerPC Linux RAMDisk Image (uncompressed)
Data Size: 0 Bytes = 0 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at ec000000
Booting using the fdt blob at 0xec000000
Loading Kernel Image ... OK
OK
Loading Ramdisk to 10000000, end 10000000 ... OK
Loading Device Tree to 00ffa000, end 00fffc78 ... OK
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
When OEM volumes are present in the [alt_]firmware partition,
sysupgrade will write a new kernel, but will fail to write
the root file system. The next boot will hang indefinitely
Waiting for root device /dev/ubiblock0_0...
Modified ipq40xx/base-files/lib/upgrade/linksys.sh
to remove both `squashfs` and `ubifs` if found
on the target firmware partition's UBI device.
Run-tested-on: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[applied some shellcheck suggestions as well]
Follow upstream changes - header file changes
no executable difference at all
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 5273fb6b21b953428e2f9ea5892872db5aaf22c1)
Move all MikroTik devices to new function to increase script execution
speed.
Machine name in new version of MikroTik RouterBOARD devices add "RB"
before model name:
Old machine name: MikroTik RouterBOARD 951Ui-2nD
New: MikroTik RouterBOARD RB951Ui-2nD
So this patch should fix it for all currently supported MikroTik boards.
Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [wAP R-2nD]
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
[rebased,commit message facelift,script fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[spotted missing 922UAGS-5HPacD]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Refreshed all patches.
Altered patches:
- 816-pcie-support-layerscape.patch
This patch also restores the initial implementation
of the ath79 perfcount IRQ issue. (78ee6b1a40)
It was wrongfully backported upstream initially and got reverted now.
Compile-tested on: cns3xxx
Runtime-tested on: cns3xxx
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
err_free_stats has been deprecated. Replace with err_netdev.
Compile-tested on: mvebu
Runtime-tested on: mvebu
Fixes: 4089df4f4b ("kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)")
Signed-off-by: George Amanakis <gamanakis@gmail.com>
[altered hashes]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 1e3800df1808b4a5a977c3a9651958611df51c83)
It's needed for applying some hardware quirks. This fixes:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/dmi.c:60:20: error: 'DMI_PRODUCT_SKU' undeclared here (not in a function); did you mean 'DMI_PRODUCT_UUID'?
DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "T8"),
Fixes: c52054e568 ("mac80211: brcm: backport remaining brcmfmac 5.2 patches")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 4d11c4c3784196ed3e5b5a1f81fa415d99ef32b0)
Memory is allocated with devm_kzalloc() on every page program
and leaks until device is closed (which never happens).
Convert to kzalloc() and handle error paths manually.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Refreshed all patches.
This bump contains upstream commits which seem to avoid (not properly fix)
the errors as seen in FS#2305 and FS#2297
Altered patches:
- 403-net-mvneta-convert-to-phylink.patch
- 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch
Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* Remove testing patches for kernel version 4.19
* remove targets ar7, ixp4xx, orion
Those targets are still on kernel 4.9, patches for 4.14 were not ready
in time. They may be readded once people prepare and test patches for
kernel 4.14.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
01_leds has several redundant LED-cases. This commit cleans
up the file by merging these cases into shared cases.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
The TP-Link Archer C25 is a low-cost dual-band router.
Specification:
- CPU: Atheros QCA9561 775 MHz
- RAM: 64 MB
- Flash: 8 MB
- Wifi: 3x3 2.4 GHz (integrated), 1x1 5 GHz QCA9887
- NET: 5x 10/100 Mbps Ethernet
Some LEDs are controlled by an additional 74HC595 chip, but not
all of them as e.g. for the C59.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ASUS RP-N53 and Buffalo WHR-600D use RT5592 for 5GHz wireless
After commit 367813b9b1 the driver for RT5592 (rt2800pci)
is not selected by default anymore, which broke their 5GHz wireless
Add it back to device packages
Fixes: 367813b9b1 ("ramips: mt7620: fix dependencies")
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
When upgrading a TP-Link Archer C7 v2 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Some people subtitute the unsupported QCA9880v1 in the Archer v1
with supported QCA9880v2 radio. Since the stock radio doesn't
work, so it's safe to apply the change also for the Archer v1
images as well.
Also this patch renames the migration file and variables from
wmac to wifi.
Signed-off-by: David Santamaría Rogado <howl.nsp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[removed comment, added return 0 (not that it matters since uci is
clever, see 00-wmac-migration thread), reworded commit message]
This patch harmonizes the label and alias for art partitions
across ath79. Since lower case seems to be more frequent, use that
consistently.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In commit c3a8518 eth0 and eth1 have been swapped for some devices,
but 11-ath10k-caldata has not been updated.
Instead of fixing this by swapping eth0/eth1, this patch will read
addresses from flash (as done for several devices already) so
adjustments due to eth order become obsolete.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The info/product-info partition, which frequently contains MAC
adresses, is typically assigned the 'info' alias in DTS, but
then labelled with 'info', 'product-info' or 'config'.
This leads to different aliases if used for setting MAC adresses
in DTS compared to when using e.g. mtd_get_mac_binary. Occationally,
also multiple switch-case entries are used just because of different
labelling.
This patch relabels those partitions in ath79 to consistently use
'info'.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Converts the TP-Link WDR4900 v1 to use the simpleImage in the
hopes of prolonging the life of the device. While at it,
the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE
to 2684 KiB as a precaution since the stock u-boot is using a
fixed kernel size.
Note: Give the image some time, it will take much longer to
extract and boot.
[tested for 4.14/4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
In commit d2e18dae28 ("kirkwood: cleanup image build code") the image
build code was refactored, setting KERNEL_IN_UBI=0 which doesn't work as
the KERNEL_IN_UBI needs to be unset in order to make it working as
intended, which leads to factory images with two kernels in them:
binwalk --keep-going openwrt-kirkwood-cisco_on100-squashfs-factory.bin
MD5 Checksum: c33e3d1eb0cb632bf0a4dc287592eb70
DECIMAL HEX DESCRIPTION
-------------------------------------------------------------------------------
0 0x0 uImage header [...] "ARM OpenWrt Linux-4.14.123"
5769216 0x580800 uImage header [...] "ARM OpenWrt Linux-4.14.123"
Cc: Mathias Kresin <dev@kresin.me>
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=2285
Fixes: d2e18dae28 ("kirkwood: cleanup image build code")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The "bridge allow reception on disabled port" implementation
was broken after these commits:
08802d93e2 ("kernel: bump 4.19 to 4.19.37")
b765f4be40 ("kernel: bump 4.14 to 4.14.114")
456f486b53 ("kernel: bump 4.9 to 4.9.171")
This leads to issues when for example WDS is used, tied to a bridge:
[ 96.503771] wlan1: send auth to d4:5f:25:eb:09:82 (try 1/3)
[ 96.517956] wlan1: authenticated
[ 96.526209] wlan1: associate with d4:5f:25:eb:09:82 (try 1/3)
[ 97.086156] wlan1: associate with d4:5f:25:eb:09:82 (try 2/3)
[ 97.200919] wlan1: RX AssocResp from d4:5f:25:eb:09:82 (capab=0x11 status=0 aid=1)
[ 97.208706] wlan1: associated
[ 101.312913] wlan1: deauthenticated from d4:5f:25:eb:09:82 (Reason: 2=PREV_AUTH_NOT_VALID)
It seems upstream introduced a new patch, [1]
so we have to reimplement these patches properly:
target/linux/generic/pending-4.9/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.14/150-bridge_allow_receiption_on_disabled_port.patch
target/linux/generic/pending-4.19/150-bridge_allow_receiption_on_disabled_port.patch
[1] https://lkml.org/lkml/2019/4/24/1228
Fixes: 08802d93e2 ("kernel: bump 4.19 to 4.19.37")
Fixes: b765f4be40 ("kernel: bump 4.14 to 4.14.114")
Fixes: 456f486b53 ("kernel: bump 4.9 to 4.9.171")
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
[updated commit message and title]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
ctinfo is a new tc filter action module. It is designed to restore
information contained in firewall conntrack marks to other packet fields
and is typically used on packet ingress paths. At present it has two
independent sub-functions or operating modes, DSCP restoration mode &
skb mark restoration mode.
The DSCP restore mode:
This mode copies DSCP values that have been placed in the firewall
conntrack mark back into the IPv4/v6 diffserv fields of relevant
packets.
The DSCP restoration is intended for use and has been found useful for
restoring ingress classifications based on egress classifications across
links that bleach or otherwise change DSCP, typically home ISP Internet
links. Restoring DSCP on ingress on the WAN link allows qdiscs such as
but by no means limited to CAKE to shape inbound packets according to
policies that are easier to set & mark on egress.
Ingress classification is traditionally a challenging task since
iptables rules haven't yet run and tc filter/eBPF programs are pre-NAT
lookups, hence are unable to see internal IPv4 addresses as used on the
typical home masquerading gateway. Thus marking the connection in some
manner on egress for later restoration of classification on ingress is
easier to implement.
Parameters related to DSCP restore mode:
dscpmask - a 32 bit mask of 6 contiguous bits and indicate bits of the
conntrack mark field contain the DSCP value to be restored.
statemask - a 32 bit mask of (usually) 1 bit length, outside the area
specified by dscpmask. This represents a conditional operation flag
whereby the DSCP is only restored if the flag is set. This is useful to
implement a 'one shot' iptables based classification where the
'complicated' iptables rules are only run once to classify the
connection on initial (egress) packet and subsequent packets are all
marked/restored with the same DSCP. A mask of zero disables the
conditional behaviour ie. the conntrack mark DSCP bits are always
restored to the ip diffserv field (assuming the conntrack entry is found
& the skb is an ipv4/ipv6 type)
e.g. dscpmask 0xfc000000 statemask 0x01000000
|----0xFC----conntrack mark----000000---|
| Bits 31-26 | bit 25 | bit24 |~~~ Bit 0|
| DSCP | unused | flag |unused |
|-----------------------0x01---000000---|
| |
| |
---| Conditional flag
v only restore if set
|-ip diffserv-|
| 6 bits |
|-------------|
The skb mark restore mode (cpmark):
This mode copies the firewall conntrack mark to the skb's mark field.
It is completely the functional equivalent of the existing act_connmark
action with the additional feature of being able to apply a mask to the
restored value.
Parameters related to skb mark restore mode:
mask - a 32 bit mask applied to the firewall conntrack mark to mask out
bits unwanted for restoration. This can be useful where the conntrack
mark is being used for different purposes by different applications. If
not specified and by default the whole mark field is copied (i.e.
default mask of 0xffffffff)
e.g. mask 0x00ffffff to mask out the top 8 bits being used by the
aforementioned DSCP restore mode.
|----0x00----conntrack mark----ffffff---|
| Bits 31-24 | |
| DSCP & flag| some value here |
|---------------------------------------|
|
|
v
|------------skb mark-------------------|
| | |
| zeroed | |
|---------------------------------------|
Overall parameters:
zone - conntrack zone
control - action related control (reclassify | pipe | drop | continue |
ok | goto chain <CHAIN_INDEX>)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make suitable adjustments for backporting to 4.14 & 4.19
and add to SCHED_MODULES_FILTER
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
All patches of LSDK 19.03 were ported to Openwrt kernel.
We still used an all-in-one patch for each IP/feature for
OpenWrt.
Below are the changes this patch introduced.
- Updated original IP/feature patches to LSDK 19.03.
- Added new IP/feature patches for eTSEC/PTP/TMU.
- Squashed scattered patches into IP/feature patches.
- Updated config-4.14 correspondingly.
- Refreshed all patches.
More info about LSDK and the kernel:
- https://lsdk.github.io/components.html
- https://source.codeaurora.org/external/qoriq/qoriq-components/linux
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to convert to use TF-A for firmware.
- Use un-swapped rcw since swapping will be done in TF-A.
- Use u-boot with TF-A defconfig.
- Rework memory map for TF-A introduction.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Petr Štetiar