Some boards with JBOOT have partiton between bootloader
and kernel image. This patch add possibility to change kernel
partition start address.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The cmake bump to 3.14.0 breaks build on all targets. Revert it for now.
This reverts commit a3446257a8.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Update CMake to 3.14.0
Refresh patches
Remove inofficial fossies.org and replace with GitHub (link on official site)
Remote 150-C-feature-checks-Match-warnings-more-strictly.patch as it's
a no longer needed backport from upstream.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range
extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros
QCA9558 + QCA9882 + AR8035 platform and is available only on US market.
Specification:
- 720/600/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of flash (SPI NOR)
- 1x 1 Gbps Ethernet (AR8035)
- 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11)
- 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11)
- 2x U.FL connector on PCB
- 2x dual-band PCB antennas
- 1x LED, 2x dual-color LED (all driven by GPIO)
- 3x button (app config, led, reset)
- 1x mechanical on/off slide switch
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x JTAG (8-pin, 1.27 mm pitch) header on PCB
Flash instruction:
Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254,
default credentials: admin/admin).
Warning:
This device does not include any kind of recovery mechanism in U-Boot.
Vendor firmware access:
You can access vendor firmware over serial (RX line requires jumper
resistor in R306 place, near XTAL) with: root/sohoadmin credentials.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Require the word "warning" to appear at the start of a line, after
whitespace, or after a `:`. This is the same that CTest launchers use
to match warnings. It avoids matching "warning" inside file paths.
Fixed in cmake 3.14.0.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
Fixes timeouts with trying to access the FTP site.
Also remove mirror2.openwrt.org, which does not keep current tarballs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gnu date is present in our staging_dir which means squashfskit will fail
to build. Prevent also a race condition if coreutils is build after
squashfskit.
To prevent a race condition, depend on coreutils.
Acked-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
squashfskit is a fork of the squashfs-tools.
squashfskit creates reproducible filesystems and includes
many of the distro patches.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Tested-by: Paul Spooren <mail@aparcar.org>
This makes OpenWrt build an Ext2+Ext4 partitioned image
for the D-Link DNS-313 with two blank partitions, a boot
partition on /dev/sda3 and a rootfs partition on
/dev/sda4.
This uses the methods already used in apm821xx including
the tricks to convert the generated Ext2 filesystem
partition to version 1 so that the firmware bootloader
will properly recognize it.
We patch a bit around the build files to make sure we
get the rootfs size set and that genext2fs is properly
built.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Fixing and tricksing]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The firmware on the D-Link DNS-313 NAS require two blank
partitions before the boot partition. Support this if
explicitly requested with a "-n" flag.
Tested on the D-Link DNS-313.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[Broken out from original patch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update mpfr to 4.0.2
Use official site as last resort
Force thread-safety functionality
Refresh patches
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Fix for factory image generation, so that stock firmware will accept the
openwrt image.
Ref: https://forum.openwrt.org/t/support-for-tp-link-archer-c2-v3/15617/17
Signed-off-by: Skirmantas Lauzikas <skirmantas.lauzikas@blackraven.lt>
[reword commit message, use correct order for conditions,
trim trailing whitespace]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Move the zip compression into a build recipe. Pad the image using the
existing build recipes as well to remove duplicate functionality
Change the code to append header and footer in two steps. Allow to use a
fixed filename as the netgear update image does.
Use a fixed timestamp within the zip archive to make the images
reproducible.
Due to the changes we are now compatible to the gnu89 c standard used by
default on the buildbots and we don't need to force a more recent
standard anymore.
Beside all changes, the footer still looks wrong in compare to the
netgear update image.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the option -mt/--mtime to pass a timestamp which is used as filedate
for the containing files.
So far, it isn't used for anything written to the extra fields,
therefore requires the -X (eXclude eXtra file attributes) parameter to
be effective.
Signed-off-by: Mathias Kresin <dev@kresin.me>
One image requires a zip compressed image, so add the zip util found in
the packages feed, and extend it with some useful debian patches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
While we don't need the gnu99 option anymore, we still need to force the
c99 standard to fix the following build error on the build bots:
src/mkdlinkfw.c: In function 'find_auh_headers':
src/mkdlinkfw.c:267:3: error: 'for' loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < header_counter; i++) {
^
src/mkdlinkfw.c:267:3: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
Signed-off-by: Mathias Kresin <dev@kresin.me>
fread() doesn't set errno, ferror need to be used to check for errors.
While at it, check if we read the expect number of elements.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the SOURCE_DATE_EPOCH environment variable if set instead of the
current time. The used timestamp matches the timestamp of the latest
commit this way and make the images reproducible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Drop unused function and macros. With the cleanup the gnu extension
typeof isn't used any longer and the gnu99 compile flag can be dropped.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch adds support for TP-Link Archer C6 v2 (EU)
Hardware specification:
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q64CSIG (8MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: There's no UART header on the board
Flash instructions:
Upload
openwrt-ath79-generic-tplink_archer-c6-v2-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherC6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the reset
button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
According to the GPL source the non-EU variant has different
GPIOs assigned to some of the LEDs and buttons. The flash
layout might be different as well. The wikidevi entry for
Archer A6/C6 assumes they are identical.
Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com>
This commit adds "hex pattern mode" to xorimage. This mode allows xor
with a hexadecimal pattern that cannot be expressed with ASCII
charactors.
usage (example):
xorimage -i firmware.bin -o firmware.bin.new -p 6A57190601121E4C -x
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (fix checkpatch)
- it appears (at least from OS X verison 10.10, Yosemite) that the
big and little endian defintions have changed.
the older
#include <sys/_endian.h>
#include <architecture/byte_order.h>
reference yielded the following warning:
#define __bswap_16(x) NXSwapShort(x)
^
/usr/include/architecture/byte_order.h:45:1: note: 'NXSwapShort' has been explicitly marked deprecated here
For the new OS X editions, it seems that we need to refer to:
#include <netinet/in.h>
#include <libkern/OSByteOrder.h>
and respectively use 'OSSwapInt16', 'OSSwapInt32', & 'OSSwapInt64', in
place of 'NXSwapShort', 'NXSwapLong' & 'NXSwapLongLong'.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This patch adds support for TP-Link Archer A7
Specification:
- SOC: QCA9563
- Flash: 16 MiB (SPI)
- RAM: 128 MiB (DDR2)
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) SoC internal
- 5GHz (ac) QCA988x
- USB: 1x USB 2.0 port
- Button: 1x power, 1x reset, 1x wps
- LED: 10x LEDs
- UART: holes in PCB
- Vcc, GND, RX, TX from ethernet port side
- 115200n8
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-a7-v5-squashfs-factory.bin
via the Webinterface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the Archer A7
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the tftp
root directory renamed to ArcherC7v5_tp_recovery.bin
2. Connect power cable to Archer A7, press and hold the reset button
and turn the router on
3. Keep the reset button pressed for ~5 seconds
4. Wait ~150 seconds to complete flashing
Changes since first revision:
- Flash instructions using stock image webinterface
- Changed "Version 5" in model string to "v5"
- Split DTS file in qca9563_tplink_archer-x7-v5.dtsi
and qca9563_tplink_archer-a7-v5.dts
- Firmware image is now build with dynamic partitioning
- Default to ath10k-ct
Changes since second revision:
- Changed uboot@0 to uboot@20000 in DTS file
- Fixed ordering issue in board led script
- Specify firmware partition format in DTS file
- Rebased Makefile device definition on common
Device/tplink-safeloader-uimage definition
- Merged switch section in network script
(same configuration as tplink,tl-wdr3600
and tplink,tl-wdr4300)
Signed-off-by: Karl-Felix Glatzer <karl.glatzer@gmx.de>
The ufb tool needs the host UAPI Linux headers from kernel 3.18
or later, remove it for now as it is not used anyway.
Fixes: 4bf5c4395b ("tools/sdimage: update to latest git version")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This includes code cleanups and fixes some portability issues,
compiler warnings about printf arguments etc.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Drop the factory images and the firmware tool to create them. They don't
work any more, since the factory image has an uImage header covering the
whole kernel + rootfs. This way the uImage splitter will not be able to
find the rootfs and the kernel will panic later on.
The factory images were most likely added at a time the board had
distinct partitions for kernel and rootfs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Some packages like libpfring assume the presense of lex, which on some
other systems is a symlink to flex but not all. Symlink flex to fix
compilation.
Arch Linux and Fedora do this as far as I know.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Currently flash from WebIF is broken for Archer C7 v5 EU models as their
SupportList entries are missing.
The added entries originate from TP-Links latest Archer C7 v5 EU
firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
Chnages since 3.2:
b590ad02 version 3.2.1
05e70adf build: fix issues in the generated tarball
7efe0b5d build: fix typo
351e3630 NEWS: update
4fd1fc70 examples: ship them
e02ce4c7 build: minor fixes in doc/
7cab285e CI: maximize chances of errors sooner
86efe282 c++: improve the generated documentation
cf1446dc tests: don't fail if the C++ compiler does not work
e93c40b3 tests: don't disable C++ warnings in C files
eff67391 c++: workaround portability issue
5a0d7802 tests: work around getopt portability issues
f1e0839c doc: -Wzero-as-null-pointer-constant was added to GCC 4.7
3bf429ae examples: #include <cstring> in calc++
f8cadc73 c: provide a definition of _Noreturn that works for C++
bd7aebb8 c: update the definition of _Noreturn
ca8039e6 tests: don't expect the shell to support 'local'
5d07f4f7 bitset: fix warning
e605ad96 build: fix use of gnulib Make variables
50fac71d maint: post-release administrivia
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Deng Qingfang