During porting support for this router to ath79 target
it was discovered that GPIO mapping was incorrect (GPIO11 active high).
Correct mapping for both V1 and V2 is GPIO12 active low.
Default configuration from GPL source for V2 explicitly states this, and
this was confirmed experimentally on ath79 by looking on
/sys/kernel/debug/gpio. Correctness of this was also validated for V1 by
cross-flashing vendor firmware for V1 on V2 hardware, in which reset
button also worked.
Fix it.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[slightly adjust commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f841e706403b1a111cbb6dc5930b7886307bf633)
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de06 ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit b017a016cc0cd26f84a7e6b8de3dc02dc101e888)
The -O option for the tplink-v1-header was missing for the TP-Link
TL-WR902AC v1, while safeloader and MTDPARTS where set up with a
single firmware partition.
This led to bootloops after using sysupgrade.
Fixes: FS#3118
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a7b07f8ba880895f0d235a63729dd189cb2410a7)
So far, specifying "BOARD_NAME := routerboard" is required by the
upgrade code of Mikrotik NAND devices, as "sysupgrade-routerboard"
is hardcoded in platform_do_upgrade_mikrotik_rb().
This patch replaces the latter with a grep for the name like it
is already done in nand_upgrade_tar() in /lib/upgrade/nand.sh.
This should enable upgrades from ar71xx to ath79 without setting
BOARD_NAME for the latter.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(backported from commit 281785d74fcc70153c0741be36ee1f9d05e74f6f)
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.
Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k. Since ath10k caldata is no longer pulled from
this implementation, this commit also disables the publication in sysfs
to avoid wasting memory.
Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Fetch ath10k calibration data from backported mikrotik sysfs driver
which supports the newer "LZOR" encoding.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Refreshed all patches and removed upstreamed:
oxnas/001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch
oxnas/002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch
Fixes: CVE-2020-12114 and CVE-2020-11669
Runtime-tested on: qemu-x86-64
Compile-tested on: ath79/generic, x86/64, imx6
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Without this patch, when using rev 3 of the Atheros AR9344 SoC, the
gigabit switch (AR8327) does not work or works very erratically.
This is a re-spin of http://patchwork.ozlabs.org/patch/419857/ with a
different PLL value, according to the feedback from several users
(including myself) as shown here:
https://openwrt.org/toh/mikrotik/rb2011uias#tracking_reported_experience_with_suggested_patch_for_the_5_gige_ports
Performance is acceptable: testing L3 forwarding without NAT yields a
performance of 370 Mbit/s (iperf3 TCP) and 41 Kpps (iperf3 UDP with 64
bytes payload). Both tests show that 100% of CPU time is spent on softirq.
A similar fix for a different device (RB2011) was added in e457d22261
("Make GBit switch work on RB2011").
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
(cherry picked from commit 247043c968d22c193055a97a9cdf5baef4aaf96d)
Use power led for device status.
The status led behavior has already been fixed in af28d8a539
("ath79: add support for GL.iNet GL-AR750S") when porting the
device to ath79. This fixes it for ar71xx as well.
Signed-off-by: Jan Alexander <jan@nalx.net>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d394c354ee0e8660f876889f6293803c581cbf85)
The labels on the LAN ports of the TP-Link Archer C60 v1/v2 are
actually inverted compared to the ports of the internal switch.
Add this information to 02_network.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14a07fa1f000f962d55bf53cfe9b128448b1f11f)
The adjustment of the MAC address for Archer C60 v2 in 10_fix_wifi_mac
is broken since a "mac" partition is not set up for this device on
ar71xx. Instead, the MAC address is already patched correctly in
11-ath10k-caldata.
Remove the useless adjustment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit cbdc91902466dd113b9680566abb2eb2f8022dd4)
The MAC addresses for lan/wan are swapped compared to the vendor
firmware. This adjusts to vendor configuration, which is:
lan *:7b label
wan *:7c label+1
2.4g *:7b label
5g *:7a label-1
Only one address is stored in <&mac 0x8>, corresponding to the label.
This has been checked on revisions v1, v2 and v3.
Since ar71xx calculates the ath10k MAC address based on the ethernet
addresses, the number there is adjusted, too.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 14eb54938b525d4c2d2847a6fad7670ed944650c)
Because the WPS button had the wrong trigger level,
the failsafe mode was triggered quite often,
after this commit:
https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=27f3f493de
Signed-off-by: Catrinel Catrinescu <cc@80211.de>
(cherry picked from commit 3e03b7ac4ada4966d058871d0a1f67f1f0f408d4)
When changing the LED names for the Archer C7 to represent the correct
color, a migration for existing UCI entries was not created.
Add a migration to keep existing LED configurations working.
Fixes commit c79c001b593b ("ar71xx: Archer C7 v1 LED names and RFKILL
fixes")
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4349d4c6823bfe09caabbdd3c9a65198addc76d6)
The AVM FRITZ!WLAN Repeater 450E's WPS button is not active low.
Correct the active low flag to avoid unintenional activation of
failsafe mode on boot.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1d4f2ca6105698fde3b997c32e7e41f080c79a15)
Change u-boot-env partitions to be mounted as read-write for gl-ar150,
gl-domino and gl-mifi so uboot-envtools support is possible.
Signed-off-by: Kimmo Vuorinen <kimmo.vuorinen@gmail.com>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 2c1cfacddedc82c7a34eeb2a26529a5f3ab423d8)
When mapping for RSSI LEDs was defined for interface wlan0 on
Ubiquiti Rocket M Titanium, it missed connection to actual interface.
Therefore create the mapping to interface, so RSSI LEDs work without
additional configuration, after starting rssileds service.
While at that, split RSSI into ~equal intervals for 6 LEDs,
and remove coefficients needed for PWM LEDs, as this board does not
support PWM LEDs.
Finally, for complete support, enable 'rssileds' package in per-device
rootfs, so the indicator works out of box.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
(cherry picked from commit 83708f233daceacebd1c49da44711cc87b49162a)
This image is only needed on one device (wAP AC); since this target is
going to be removed anyway it doesn't make sense to add an extra "low
RAM" image.
Fixes OOM issues on RouterBoard wAP AC.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
(cherry picked from commit 788c8485eb5b71ef7e7b2a2d3077772e526e9746)
The current ethernet MAC address setup of TL-WDR4300 board is different
from the setup of stock firmware:
OpenWrt: lan = label_mac -2, wan = label_mac -2
stock: lan = label_mac, wan = label_mac +1
This patch applies to all devices using TL-WDR4300 board:
TL-WDR3600 v1
TL-WDR4300 v1
TL-WDR4300 v1 (IL)
TL-WDR4310 v1
Mercury MW4530R v1
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
(cherry picked from commit 9b02d32e34df2bb8821ec6f08f525bee22d0d1ba)
In order to make RSSI indicator on the device work out of box,
include "rssileds" package in per-device rootfs image by default
for Ubiquiti XM and XW devices, namely:
- Bullet M (XM/XW)
- Rocket M (XM/XW)
- Nanostation M (XM/XW)
- Nanostation Loco-M (XW)
This moves the package addition to the individual devices in order
to prevent accidental inclusions of the package when not looking
at the parent node carefully enough.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[add bullet-m-xw, remove rocket-m-ti, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 08d9c95417399ac8615df210f4381cca68a4b25c)
TP-Link TL-WDR4900 v2 only has one combined WPS/Reset button, so
don't set up an RFKILL for this device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 25127f58b42d794bd47d56ea107f3dfc9cc4816c)
In ar71xx there is only one combined mach file for Archer C5/C7 and
TL-WDR4900 v2. This one uses the same LED struct for all devices,
defining "green" LEDs for them. However, WDR4900 uses blue front
LEDs, while only C5/C7 uses green ones. Despite, in base-files
WDR4900 is actually set up with "blue" for the mentioned LEDs.
Thus, this patch creates a separate LED struct for WDR4900, so the
LEDs can be set up correctly. Despite, the wlan5g LED is removed as
it is controlled by ath9k chip for WDR4900 (in contrast to C5/C7).
Note: While front LEDs are blue, USB LEDs (on the back) are green,
so colors are mixed intentionally for the WDR4900 v2.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 93f2bcc35e371ec0c4ceb76c06f90b898c726ba5)
The MAC address setup of the TL-WDR4900 v2 is different from the
C5/C7. This aligns ar71xx with the setup in ath79:
wlan0 (5GHz) : -2
wlan1 (2.4GHz) : -1
eth1 (LAN) : 0
eth0 (WAN) : 1
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a9d3084b83bb2d0fa2c0b43bf2a0831b5ae1df13)
As discussed in 1d18a14a90 ("ath79: really fix TP-Link Archer C7
v2 MAC address"), stock firmware MAC address assignment is
actually as follows:
wlan0 (5GHz) : -1
wlan1 (2.4GHz) : 0
eth1 (LAN) : 0
eth0 (WAN) : 1
This has never been fixed for ar71xx, so let's do it now.
Note that with WDR4900 v2 even both wlan0 and wlan1 where assigned
to basemac-1 before ...
Fixes: FS#408
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit a021268032fb64afdce7bafa91c7c7bf44fa6ff2)
Fix the error that tl-wdr3320-v2 can't upgrade firmware via web
interface by using magic_ver="0200" for this device.
Signed-off-by: 南浦月 <nanpuyue@gmail.com>
[commit message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 0ff2385a92c0a31769fce954b7bd571d6114dbc8)
This fixes commit bae927c551 ("ar71xx: add support for TP-LINK CPE510
V2.0") where the support for this device wasn't optimal.
Device support for the CPE510v2 so far has been a hack to enable
flashing with CPE510v1 images. Those even have different hardware (e.g.
additional ethernet port).
With this patch, we provide proper support for this device in ar71xx.
Installation:
- Flash factory image through stock firmware WEB UI or through TFTP
- To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
- Rename factory image to recovery.bin
- Stock TFTP server IP: 192.168.0.100
- Stock device TFTP address: 192.168.0.254
Fixes: bae927c551 ("ar71xx: add support for TP-LINK CPE510 V2.0")
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
[Rebased onto revert commit, changed comments in mach-cpe510.c,
changed commit title and description, fixed eth0 MAC address,
removed eth1 initialization]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[squashed revert, added fixes tag]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c79b796280fa5cd64bac663f9d5e5d9a737c30d6)
[added CPE510V2 entry to tplink-safeloader.c]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2bc7c519dcc0e7ca09feed24a3b9a105bc49f423)
Signed-off-by: David Bauer <mail@david-bauer.net>
There is md5 sum of whole image embedded in combined-image header which
is checked on sysupgrade. The check will fail for ath79 images which
may have embedded metadata. This is because metadata are appended after
the combined image is created. To allow smooth transition from ar71xx to
ath79, strip metadata before calculating md5 sum for whole image.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
(cherry picked from commit 8b4109c2b4d60495d046157d1baca9b1cdbf8dc8)
Now that $UPGRADE_BACKUP is set conditionally there is no need to check
the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit a858db313687ddfa6ed1ddba76bd74844a7b89dc)
Move the IRQ fix from generic to ar71xx specific.
Other targets like ath79 have specific pathes to delete this code.
This resulted in a build failure on ath79
Fixes: 00d48bcac08a ("ar71xx: Fix potentially missed IRQ handling during
dispatch")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Lech Perczak