Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
There are only artifacts for these boards in our tree and not even
partial support.
Drop teh stale files.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 30f61a34b4 claimed to drop -d & -p
options. In reality only -d was dropped. Update command help text to
reflect that -d is no longer a supported option.
Fixes FS#1187
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
More important bug fix:
402f05c Use full-rate mtu_time in all tins. Fixes an issue where some
cake tins experienced excessive latency since 49776da (dynamically
adjust target)
Minor bug fixes:
31277c2 Avoid unsigned comparison against zero. Fix compiler warning,
no known impact.
8cf5278 ack_filter: fix TCP flag check. A very contrived case may have
lead to dropping a SYN packet that should not be dropped.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Certain DHCP servers push a gateway outside of the assigned interface subnet,
to support those situations, install a host route towards the gateway.
If Gateway and IP are served in same network, openwrt quagga cannot learn
routes (rip routes are not getting added, showing inactive) whereas
working fine when Gateway and IP are in different network.
Signed-off-by: Mogula Pranay <mogula.pranay@nxp.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the
original netdev might disappear before br2684ctl has finished appling it's
setting:
local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully
local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC
kern.info kernel: dsl0: renamed from nas0
kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device
local2.err br2684ctl[1667]: Could not configure interface:No such device or address
By passing the final used netdev name to br2684ctl_wrap another race
condition workaround will be enabled again.
Change the lantiq ptm driver to create a netdev with the name dsl as well.
Albeit the rename via 'ip link' works fine so far, using a different
approach for ptm then atm could be confusing.
Signed-off-by: Mathias Kresin <dev@kresin.me>
br2684ctl starts automatically, set up reload triggers, which fire as soon
as a atm driver is loaded. No need to do the reload via the script.
The reload is only required as soon as we can reliable switch between atm
and ptm driver and need to be implemented in a race free way.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.
It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathis Kresin <dev@kresin.me>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed to generate the image, better mark them hidden
so we will activate them based on which boards gets build and they will
be activated always when the board which needs then gets build.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The fixes following problems
1. changing prefix at91bootstrap to AT91bootstrap will fix the default
selection of at91bootstrap for the selected sama5 subtarget.
2. fixed missing default selection of sama5d4 nand flash for the
selected sama5d4 subtarget.
3. corrected at91bootstrap Title name.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
neon and VFPv4 support is added to this target and uboot-at91 build
fails due to TARGET_CFLAGS -mfloat-abi set to hard. as a fix, setting
uboot-at91 CFLAGS -mfloat-abi=soft.
Fixes: 01cc6bd495 ("at91: sama5: activate fpu")
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Fixes the following dependency error encountered by the buildbots:
Package kmod-w1 is missing dependencies for the following libraries:
hwmon.ko
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
add an uboot able to boot a kernel in an ubi partition
This uboot also has a "recovery" feature, before
booting from flash it will try to boot a initramfs
image called "initramfs.bin" from a FAT32-formatted
USB drive connected to the USB 2.0 port.
(u-boot lacks drivers for usb 3.0 controllers)
Just rename the initramfs image and place it on
the usb drive, the uboot will load it.
In case there is no USB drive or no such file
is found, the uboot will boot from internal flash.
The whole check takes less than a second, boot times
are not impacted.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Use <manufacturer>_<modelname> as image name.
Use the BOARD_NAME variable to ensure that the former used boardname is
still used as the subdirectory name for the sysupgrade-tar image, to
not break sysupgrade from earlier versions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Build the Seagate GoFlexHome u-boot for the Seagate GoFlexNet as well. The
name clearly indicates that the u-boot can be used for both boards
Build the Zyxel NSA310 u-boot if the NSA310B image is selected.
Signed-off-by: Mathias Kresin <dev@kresin.me>
No image build code for the Guruplug, Sheevaplug and NSA310S exists. Drop
support for the boards for now.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Use the "low" and "high" values to configure the GPIO as an output with
that initial value. It ensures that the gpio doesn't have a unwanted value
during the time the direction is set to ouput and the actual value is
applied.
We don't need to take care of the GPIO polarity for now, since our
exported GPIOs are always active low.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Start gpio_switch before the boot state is set to up/initialised/done.
This way the exported GPIOs are available at the time rc.local is started.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Previously this was only activated for ADSL, this patch activates the
same setting also for VDSL, this feature is also support for VDSL in the
same way it works for ADSL.
I tested it with DSL FW 5.7.9.5.1.7 against a Broadcom 177.140 DSLCO
(Deutsche Telekom) and saw different data rates and Max. Attainable Data
Rates depending on the ds_snr_offset settings I choose.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The previous commit was incorrectly rebased and referred to a not
yet existing PROJECT_GIT variable.
Fixes: d86a269c1f libubox: update to latest git HEAD
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
2a9a6ea libfstools: optimize building directory string for glob
de6b026 libfstools: support file paths longer than 255 chars
Signed-off-by: John Crispin <john@phrozen.org>
The NXP 74HC164 GPIO expander driver uses a different config symbol
("CONFIG_GPIO_74X164") and module name since since at least Kernel
version 2.6.37.
Update the kmod package definition accordingly by adjusting kconfig
and module file names.
This unrelated, but correct change has been separated from the
WNR2000v5 support commits.
Ref: https://github.com/lede-project/source/pull/1256
Suggested-by: Raphael Catolino <raphael.catolino@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Instead of inferring the availability of NEON support from the target
optimization flags, use a preprocessor test to decide whether to enable
ARMv8 NEON optimizations.
Fixes the following build error spotted by the mediatek/32 buildbot:
[ 26%] Building C object CMakeFiles/zlib.dir/contrib/arm/inflate.o
In file included from .../zlib-1.2.11/contrib/arm/chunkcopy.h:10:0,
from .../zlib-1.2.11/contrib/arm/inflate.c:87:
.../arm_neon.h:31:2: error: #error You must enable NEON instructions (e.g. -mfloat-abi=softfp -mfpu=neon) to use arm_neon.h
#error You must enable NEON instructions (e.g. -mfloat-abi=softfp -mfpu=neon) to use arm_neon.h
^
In file included from .../zlib-1.2.11/contrib/arm/inflate.c:87:0:
.../zlib-1.2.11/contrib/arm/chunkcopy.h:18:9: error: unknown type name 'uint8x16_t'
typedef uint8x16_t chunkcopy_chunk_t;
^
[...]
CMakeFiles/zlib.dir/build.make:302: recipe for target 'CMakeFiles/zlib.dir/contrib/arm/inflate.o' failed
Fixes: 3acecba520 "package/libs/zlib: Add ARM and NEON optimizations"
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
In order to properly support 802.11w, hostapd needs to advertise a group
management cipher when negotiating associations.
Introduce a new per-wifi-iface option "ieee80211w_mgmt_cipher" which
defaults to the standard AES-128-CMAC cipher and always emit a
"group_mgmt_cipher" setting in native hostapd config when 802.11w is
enabled.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When using the uci.sh wrapper, allow parameters to match those supported
by the uci binary i.e. "uci rename <config>.<section>[.<option>]=<name>".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Some packages such as Python/Python3 (host pip/pip3) needs this
to compile.
More detailed explanation provided by Alexandru:
"i need the zlib/host for Python/Python3 ; because, it seems the
host pip/pip3 needs this to work ; i suspect in older versions
this worked, because some of the host's build env would be used
in the build, and then the zlib-dev from the host distro would
be used ; now, the host-build does not seem to have any
-I/usr/include stuff, which is good
and it also seems that Python/Python3 does not like it if the
zlib-dev package is too old, so using this zlib/host would be
good for this as well"
Source:
https://github.com/lede-project/source/pull/1329#issuecomment-351055861
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Add option to use O3 optimization as not all devices have
space constraints. This option is default using GCC in upstream
but isn't in the CMake makefile for some reason.
Source: https://github.com/madler/zlib/blob/master/configure#L170
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Sven Eckelmann