Tag:
Branch:
Tree:
1063d904b7
master
${ noResults }
15 Commits (1063d904b78297b3e21a352bed19bd312235ff65)
| Author | SHA1 | Message | Date |
|---|---|---|---|
Sven Eckelmann
|
ebd57de1f9 |
ipq40xx: Create /var/lock directory in platform_do_upgrade_*
The sysupgrade_pre_upgrade hook was removed with |
6 years ago |
|
Mathias Kresin
|
be06c726c4 |
treewide: drop unused get_status_led functions
The function isn't used for targets getting the status leds from the devicetree. Signed-off-by: Mathias Kresin <dev@kresin.me> |
6 years ago |
|
Mathias Kresin
|
dd448cd276 |
treewide: fix upgrade led handling
The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me> |
6 years ago |
|
Mathias Kresin
|
56b8ac1e86 |
treewide: consolidate upgrade state set
Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me> |
6 years ago |
|
Christian Lamparter
|
82618062cf |
ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
|
6 years ago |
|
Magnus Frühling
|
4b280ad91a |
ipq40xx: add support for ZyXEL WRE6606
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
|
6 years ago |
|
David Bauer
|
4fc005197a |
ipq40xx: add get_status_led to diag.sh
This commit adds the get_status_led method to diag.sh, which sets the boot-led as status-led for scripts using this method to get a status-led. This method is used platform-independent in downstream project gluon to set the LED used to indicate the config-mode. Signed-off-by: David Bauer <mail@david-bauer.net> |
6 years ago |
|
Sven Eckelmann
|
0b20490207 |
ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
|
7 years ago |
|
David Bauer
|
970f1914be |
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
|
7 years ago |
|
Robert Marko
|
1e341bb5ef |
ipq40xx: add support for 8devices Jalapeno
This patch adds support for 8devices Jalapeno. Specification: QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz 256 MB of DDR3 RAM 8 MB of SPI NOR flash 128 MB of Winbond SPI NAND flash WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN) phy@mdio3: Label: eth0 gmac0 phy@mdio4: Label: eth1 gmac1 Installation instructions: Since boards ship with old version of LEDE installation is simple. Just use sysupgrade -n -F sysupgrade.bin Syuspgrade needs to be forced since OpenWRT uses DT detection in recent releases. If you get error that FIT configuration is not found during boot it is due to older U-boot used on your board. That is because 8devices used custom FIT configuration partition name as they internally had v1 and v2 boards. Only v2 boards are sold so now they are shipping boards with never U-boot using generic config@1 FIT partition name. Also for old uboot it is possible to force loading config@1 by changing uboot environment: setenv boot5 'bootm 0x84000000#config@1’ saveenv Signed-off-by: Robert Marko <robimarko@gmail.com> |
7 years ago |
|
Sven Eckelmann
|
2796ab85ed |
ipq40xx: add support for Compex WPJ428
* QCA IPQ4028
* 256 MB of RAM
* 32 MB of SPI NOR flash (mx25l25635e)
* 128 MB of SPI NAND flash (gd5f1gq4ucy1g)
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2 fully software controllable GPIO-LEDs
* 2 additional GPIO-LEDs which also affect the SIM card detection
* 1x button (reset)
* 1x GPIO buzzer
* 1x USB (xHCI)
* 1x NGFF (USB-only with Dual-SIM support, untested)
* TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC)
* 2x gigabit ethernet
- phy@mdio4:
+ Manual: Ethernet port 0
+ gmac0 (ethaddr) in original firmware
+ 802.3af POE (HV version)
+ 24v passive POE (LV version)
- phy@mdio3:
+ Manual: Ethernet port 1
+ gmac1 (eth1addr) in original firmware
* DC Jack connector
+ 24-56V (HV version)
+ 12-24V (LV version)
The SPI NAND flash isn't supported at the moment.
The bootloader has to be updated before OpenWrt is installed to fix a
reboot problem. The nor-ipq40xx-single.img from
https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware
has to be downloaded and the transfered in u-boot via TFTP
set ipaddr 192.168.1.11
set serverip 192.168.1.10
ping ${serverip}
tftpboot 0x84000000 nor-ipq40xx-single.img
imgaddr=0x84000000 && source $imgaddr:script
The sysupgrade image can be installed directly on flash using u-boot:
sf probe
tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin
sf erase 0x00180000 +$filesize
sf write 0x84000000 0x00180000 $filesize
bootipq
The initramfs image can be started using
tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb
set fdt_high 0x83000000
bootm 0x82000000
The used SIM card slot can be changed using
# slot 1 (also enables orange LED)
echo 1 > /sys/class/gpio/gpio3/value
# slot 2
echo 0 > /sys/class/gpio/gpio3/value
It can be checked whether a SIM card is inserted in the current slot and
the red LED is subsequently on via:
echo 2 > /sys/class/gpio/export
cat /sys/class/gpio/gpio2/value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
7 years ago |
|
Chris Blake
|
4943afd781 |
ipq40xx: add Cisco Meraki MR33 Support
This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
7 years ago |
|
Christian Lamparter
|
87c42101cf |
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
7 years ago |
|
Mathias Kresin
|
249a9b35e0 |
ipq40xx: fix GL.iNet GL-B1300 support
Rename the dts file to match the used SoC type and drop the unnecessary KERNEL_INSTALL from the image build code. Remove the fixed rootfs and kernel partitions and create an image with rootfs appended after kernel. Setup a switch portmap matching the hardware and a default network/switch configuration to make make the second lan port working. Use eth0 as lan to have it consistent accross the target. Use the power LED to indicate the boot status. Sort the SoC entries within the dts by address and use dtc labels whenever possible. Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
7 years ago |
|
John Crispin
|
54b275c8ed |
ipq40xx: add target
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: John Crispin <john@phrozen.org> |
7 years ago |