Mostly works except for USB led. Flashing not tested yet. Mostly
as an example for the sprom fixup code.
Fixup values taken from GPL tarball by comparing bcm43217_map.c
with the struct in sprom.c.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41944
- adsl and lan leds are swapped.
- internetkey is labeled as hspa.
- enable status led and reset button for failsafe.
- use new leds script.
- fix switch configuration.
- remove enet0 from board_info.
- add profile.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41588
This patch also makes use of the new leds script.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41585
This adds support for Comtrend WAP-5813n.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
[jogo: refresh patches]
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 41421
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
Support for Asmax AR 1004g router
Signed-off-by: Adrian Feliks <mexit@o2.pl>
Patchwork: http://patchwork.openwrt.org/patch/4464/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39674
This adds userspace support for Sagemcom F@st 2704 router.
Signed-off-by: Marcin Jurkowski <marcin1j@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4215/
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 39672
The first preinit script 03_do_brcm63xx.sh does the right job of
exporting variables for the other subsequent preinit scripts to use
them.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
SVN-Revision: 35504
Switch to using the B53 switch driver where appropriate.
Use a non-tagged default config where it isn't confirmed to be
working.
Remove the switch configuration in preinit as the switch will now
be configured by the driver to use port isolation to prevent leakage
between lan and wan.
While at it, also provide a switch config for Neufbox 6.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
SVN-Revision: 35307
Signed-off-by: Miguel GAIO <miguel.gaio@efixo.com>
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
[jonas.gorski@gmail.com: add network config for nb6, make switch fix a
platform patch]
SVN-Revision: 32924
Build images for 96328avng and 963281TAN (untested) for three different
flash sizes: 4MB, 8MB, and 16MB.
Known issues:
* Button setup unknown, thus no fail-safe available.
* All other BCM6328 and BCM63XX issues
SVN-Revision: 32004
Add the required board definition, default config and image generation for
the T-Home Speedport W 303V Typ B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26878
Rename the DSL-274xB rev C2's board ID to "AW4139" to match the one used
for the rev C3 (same hardware) and add a fixup for C2. Also generate
images for C3.
While we are at it, rename the LEDs to conform to the Linux LED naming
conventions.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 26876
Add support for the T-Com Speedport W 500V using a special tagged image as it
identifies itself as a 96348GW, but has some gpios wired differently, and also
has only one ethernet port without a switch attached to it.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24190
The DSL-2740B/DSL-2741B rev C2 support was missing the board definition,
resulting in a kernel panic on boot.
This patch adds it, and also renames the generated image name to properly
reflect that it is for the revision C2, and for both the DSL-2740B and
DSL-2741B.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24188
Currently eth1 is hardcoded as the expected interface switches in diagmode.
This patch replaces the eth1 with the ifname, and also directly tests if
the interface specified by ifname has a switch attached.
Signed-off-by: Jonas Gorski <jonas.gorski+openwrt@gmail.com>
SVN-Revision: 24186
Jonas Gorski