kirkwood: remove linux 4.9 support

Signed-off-by: Felix Fietkau <nbd@nbd.name>
master
Felix Fietkau 6 years ago
parent fd686dfca3
commit f445953d9f
  1. 333
      target/linux/kirkwood/config-4.9
  2. 30
      target/linux/kirkwood/patches-4.9/100-ib62x0.patch
  3. 50
      target/linux/kirkwood/patches-4.9/101-iconnect.patch
  4. 32
      target/linux/kirkwood/patches-4.9/102-dockstar.patch
  5. 33
      target/linux/kirkwood/patches-4.9/103-iomega-ix2-200.patch
  6. 258
      target/linux/kirkwood/patches-4.9/104-ea3500.patch
  7. 64
      target/linux/kirkwood/patches-4.9/105-ea4500.patch
  8. 130
      target/linux/kirkwood/patches-4.9/105-goflexhome.patch
  9. 23
      target/linux/kirkwood/patches-4.9/106-goflexnet.patch
  10. 48
      target/linux/kirkwood/patches-4.9/107-01-zyxel-nsa3x0-common-nand-partitions.patch
  11. 147
      target/linux/kirkwood/patches-4.9/107-02-nsa310b.patch
  12. 173
      target/linux/kirkwood/patches-4.9/108-on100.patch
  13. 59
      target/linux/kirkwood/patches-4.9/109-pogoplug_v4.patch
  14. 35
      target/linux/kirkwood/patches-4.9/200-disable-tso.patch
  15. 10
      target/linux/kirkwood/patches-4.9/201-enable-sata-port-specific-led-triggers.patch
  16. 62
      target/linux/kirkwood/patches-4.9/202-linksys-find-active-root.patch

@ -1,333 +0,0 @@
CONFIG_ALIGNMENT_TRAP=y
CONFIG_ARCH_CLOCKSOURCE_DATA=y
CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
CONFIG_ARCH_HAS_SG_CHAIN=y
CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
CONFIG_ARCH_MULTIPLATFORM=y
CONFIG_ARCH_MULTI_CPU_AUTO=y
# CONFIG_ARCH_MULTI_V4 is not set
# CONFIG_ARCH_MULTI_V4T is not set
CONFIG_ARCH_MULTI_V4_V5=y
CONFIG_ARCH_MULTI_V5=y
CONFIG_ARCH_MVEBU=y
CONFIG_ARCH_NR_GPIO=0
# CONFIG_ARCH_OXNAS is not set
# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
CONFIG_ARCH_SUPPORTS_UPROBES=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARCH_USE_BUILTIN_BSWAP=y
CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
CONFIG_ARCH_WANT_LIBATA_LEDS=y
CONFIG_ARM=y
# CONFIG_ARMADA_THERMAL is not set
CONFIG_ARM_APPENDED_DTB=y
CONFIG_ARM_ATAG_DTB_COMPAT=y
# CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_EXTEND is not set
CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
# CONFIG_ARM_CPU_SUSPEND is not set
CONFIG_ARM_HAS_SG_CHAIN=y
# CONFIG_ARM_KIRKWOOD_CPUIDLE is not set
CONFIG_ARM_L1_CACHE_SHIFT=5
# CONFIG_ARM_MVEBU_V7_CPUIDLE is not set
CONFIG_ARM_PATCH_PHYS_VIRT=y
# CONFIG_ARM_THUMB is not set
CONFIG_ATA=y
CONFIG_ATAGS=y
CONFIG_ATA_LEDS=y
CONFIG_AUTO_ZRELADDR=y
# CONFIG_BINFMT_FLAT is not set
CONFIG_BLK_DEV_SD=y
CONFIG_BLK_MQ_PCI=y
CONFIG_CACHE_FEROCEON_L2=y
# CONFIG_CACHE_FEROCEON_L2_WRITETHROUGH is not set
# CONFIG_CACHE_L2X0 is not set
CONFIG_CLKDEV_LOOKUP=y
CONFIG_CLKSRC_MMIO=y
CONFIG_CLKSRC_OF=y
CONFIG_CLKSRC_PROBE=y
CONFIG_CLONE_BACKWARDS=y
CONFIG_COMMON_CLK=y
CONFIG_CPU_32v5=y
CONFIG_CPU_ABRT_EV5T=y
# CONFIG_CPU_BIG_ENDIAN is not set
CONFIG_CPU_CACHE_VIVT=y
CONFIG_CPU_COPY_FEROCEON=y
CONFIG_CPU_CP15=y
CONFIG_CPU_CP15_MMU=y
CONFIG_CPU_FEROCEON=y
# CONFIG_CPU_FEROCEON_OLD_ID is not set
# CONFIG_CPU_ICACHE_DISABLE is not set
CONFIG_CPU_IDLE=y
CONFIG_CPU_IDLE_GOV_LADDER=y
CONFIG_CPU_PABRT_LEGACY=y
CONFIG_CPU_PM=y
CONFIG_CPU_TLB_FEROCEON=y
CONFIG_CPU_USE_DOMAINS=y
CONFIG_CRC16=y
# CONFIG_CRC32_SARWATE is not set
CONFIG_CRC32_SLICEBY8=y
CONFIG_CRYPTO_CRC32C=y
CONFIG_CRYPTO_DEFLATE=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_DEV_MARVELL_CESA=y
CONFIG_CRYPTO_HASH=y
CONFIG_CRYPTO_HASH2=y
CONFIG_CRYPTO_HW=y
CONFIG_CRYPTO_LZO=y
CONFIG_CRYPTO_RNG2=y
CONFIG_CRYPTO_WORKQUEUE=y
CONFIG_DEBUG_LL=y
CONFIG_DEBUG_LL_INCLUDE="debug/8250.S"
CONFIG_DEBUG_MVEBU_UART0_ALTERNATE=y
# CONFIG_DEBUG_MVEBU_UART1_ALTERNATE is not set
CONFIG_DEBUG_UART_8250=y
# CONFIG_DEBUG_UART_8250_FLOW_CONTROL is not set
CONFIG_DEBUG_UART_8250_SHIFT=2
# CONFIG_DEBUG_UART_8250_WORD is not set
CONFIG_DEBUG_UART_PHYS=0xf1012000
CONFIG_DEBUG_UART_VIRT=0xfed12000
CONFIG_DEBUG_UNCOMPRESS=y
# CONFIG_DEBUG_USER is not set
# CONFIG_DLCI is not set
CONFIG_DNOTIFY=y
CONFIG_DTC=y
# CONFIG_EARLY_PRINTK is not set
CONFIG_EDAC_ATOMIC_SCRUB=y
CONFIG_EDAC_SUPPORT=y
CONFIG_EXT4_FS=y
CONFIG_FIXED_PHY=y
CONFIG_FIX_EARLYCON_MEM=y
CONFIG_FRAME_POINTER=y
CONFIG_FS_MBCACHE=y
CONFIG_GENERIC_ALLOCATOR=y
CONFIG_GENERIC_ATOMIC64=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_EARLY_IOREMAP=y
CONFIG_GENERIC_IDLE_POLL_SETUP=y
CONFIG_GENERIC_IO=y
CONFIG_GENERIC_IRQ_CHIP=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_PHY=y
CONFIG_GENERIC_SCHED_CLOCK=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
CONFIG_GLOB=y
CONFIG_GPIOLIB=y
CONFIG_GPIO_MVEBU=y
CONFIG_GPIO_SYSFS=y
CONFIG_HANDLE_DOMAIN_IRQ=y
CONFIG_HARDIRQS_SW_RESEND=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT_MAP=y
# CONFIG_HAVE_64BIT_ALIGNED_ACCESS is not set
CONFIG_HAVE_ARCH_AUDITSYSCALL=y
# CONFIG_HAVE_ARCH_BITREVERSE is not set
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_ARCH_PFN_VALID=y
CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
# CONFIG_HAVE_BOOTMEM_INFO_NODE is not set
CONFIG_HAVE_CBPF_JIT=y
CONFIG_HAVE_CC_STACKPROTECTOR=y
CONFIG_HAVE_CLK=y
CONFIG_HAVE_CLK_PREPARE=y
CONFIG_HAVE_CONTEXT_TRACKING=y
CONFIG_HAVE_C_RECORDMCOUNT=y
CONFIG_HAVE_DEBUG_KMEMLEAK=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_DMA_CONTIGUOUS=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_HAVE_NET_DSA=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_OPTPROBES=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_HAVE_PERF_REGS=y
CONFIG_HAVE_PERF_USER_STACK_DUMP=y
CONFIG_HAVE_PROC_CPU=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
CONFIG_HAVE_UID16=y
CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
CONFIG_HW_RANDOM=y
CONFIG_HZ_FIXED=0
CONFIG_HZ_PERIODIC=y
CONFIG_I2C=y
CONFIG_I2C_BOARDINFO=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MV64XXX=y
CONFIG_INITRAMFS_SOURCE=""
CONFIG_IOMMU_HELPER=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
CONFIG_IRQCHIP=y
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_IRQ_WORK=y
CONFIG_JBD2=y
CONFIG_KIRKWOOD_CLK=y
CONFIG_KIRKWOOD_THERMAL=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_NETXBIG=y
CONFIG_LEDS_NS2=y
CONFIG_LEGACY_PTYS=y
CONFIG_LEGACY_PTY_COUNT=256
CONFIG_LIBFDT=y
CONFIG_LZO_COMPRESS=y
CONFIG_LZO_DECOMPRESS=y
CONFIG_MACH_KIRKWOOD=y
CONFIG_MACH_MVEBU_ANY=y
CONFIG_MANGLE_BOOTARGS=y
CONFIG_MDIO_BOARDINFO=y
# CONFIG_MFD_MAX77620 is not set
CONFIG_MIGHT_HAVE_PCI=y
CONFIG_MMC=y
CONFIG_MMC_BLOCK=y
CONFIG_MMC_MVSDIO=y
# CONFIG_MMC_TIFM_SD is not set
CONFIG_MODULES_USE_ELF_REL=y
# CONFIG_MTD_CFI is not set
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_NAND=y
CONFIG_MTD_NAND_ECC=y
CONFIG_MTD_NAND_ORION=y
CONFIG_MTD_UBI=y
CONFIG_MTD_UBI_BEB_LIMIT=20
CONFIG_MTD_UBI_BLOCK=y
# CONFIG_MTD_UBI_FASTMAP is not set
# CONFIG_MTD_UBI_GLUEBI is not set
CONFIG_MTD_UBI_WL_THRESHOLD=4096
CONFIG_MULTI_IRQ_HANDLER=y
CONFIG_MV643XX_ETH=y
CONFIG_MVEBU_CLK_COMMON=y
CONFIG_MVEBU_MBUS=y
CONFIG_MVMDIO=y
# CONFIG_MVNETA is not set
CONFIG_MVSW61XX_PHY=y
CONFIG_NEED_DMA_MAP_STATE=y
CONFIG_NEED_KUSER_HELPERS=y
CONFIG_NEED_PER_CPU_KM=y
CONFIG_NLS=y
CONFIG_NO_BOOTMEM=y
CONFIG_OF=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_ADDRESS_PCI=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_GPIO=y
CONFIG_OF_IRQ=y
CONFIG_OF_MDIO=y
CONFIG_OF_NET=y
CONFIG_OF_PCI=y
CONFIG_OF_PCI_IRQ=y
CONFIG_OF_RESERVED_MEM=y
CONFIG_OLD_SIGACTION=y
CONFIG_OLD_SIGSUSPEND3=y
CONFIG_ORION_IRQCHIP=y
CONFIG_ORION_TIMER=y
CONFIG_ORION_WATCHDOG=y
CONFIG_OUTER_CACHE=y
CONFIG_PAGE_OFFSET=0xC0000000
CONFIG_PCI=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_DOMAINS_GENERIC=y
CONFIG_PCI_MVEBU=y
CONFIG_PERF_USE_VMALLOC=y
CONFIG_PGTABLE_LEVELS=2
CONFIG_PHYLIB=y
CONFIG_PHY_MVEBU_SATA=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_KIRKWOOD=y
CONFIG_PINCTRL_MVEBU=y
# CONFIG_PINCTRL_SINGLE is not set
CONFIG_PLAT_ORION=y
CONFIG_POWER_RESET=y
# CONFIG_POWER_RESET_BRCMKONA is not set
CONFIG_POWER_RESET_GPIO=y
# CONFIG_POWER_RESET_QNAP is not set
CONFIG_POWER_SUPPLY=y
CONFIG_RATIONAL=y
# CONFIG_RCU_STALL_COMMON is not set
CONFIG_REGMAP=y
CONFIG_REGMAP_I2C=y
CONFIG_REGMAP_SPI=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_MV=y
CONFIG_RTC_I2C_AND_SPI=y
CONFIG_RTC_MC146818_LIB=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_SATA_MV=y
# CONFIG_SCHED_INFO is not set
CONFIG_SCSI=y
CONFIG_SERIAL_8250_DEPRECATED_OPTIONS=y
CONFIG_SERIAL_8250_FSL=y
# CONFIG_SERIAL_MVEBU_UART is not set
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_SG_POOL=y
CONFIG_SOC_BUS=y
CONFIG_SPARSE_IRQ=y
CONFIG_SPI=y
CONFIG_SPI_MASTER=y
CONFIG_SPI_ORION=y
CONFIG_SPLIT_PTLOCK_CPUS=999999
CONFIG_SRAM=y
CONFIG_SRCU=y
CONFIG_SWCONFIG=y
CONFIG_SWIOTLB=y
CONFIG_SWPHY=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
CONFIG_THERMAL=y
CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
CONFIG_THERMAL_GOV_STEP_WISE=y
CONFIG_THERMAL_OF=y
CONFIG_TICK_CPU_ACCOUNTING=y
CONFIG_UBIFS_FS=y
CONFIG_UBIFS_FS_ADVANCED_COMPR=y
CONFIG_UBIFS_FS_LZO=y
CONFIG_UBIFS_FS_ZLIB=y
CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
CONFIG_USB=y
CONFIG_USB_COMMON=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_EHCI_HCD_ORION=y
# CONFIG_USB_EHCI_HCD_PLATFORM is not set
CONFIG_USB_EHCI_PCI=y
CONFIG_USB_LED_TRIG=y
CONFIG_USB_STORAGE=y
CONFIG_USB_SUPPORT=y
# CONFIG_USB_UHCI_HCD is not set
CONFIG_USE_OF=y
CONFIG_VECTORS_BASE=0xffff0000
# CONFIG_VFP is not set
CONFIG_VM_EVENT_COUNTERS=y
CONFIG_WAN=y
CONFIG_WATCHDOG_CORE=y
CONFIG_XZ_DEC_ARM=y
CONFIG_XZ_DEC_BCJ=y
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZLIB_DEFLATE=y
CONFIG_ZLIB_INFLATE=y

@ -1,30 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-ib62x0.dts
+++ b/arch/arm/boot/dts/kirkwood-ib62x0.dts
@@ -5,7 +5,7 @@
/ {
model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
- compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ compatible = "raidsonic,ib-nas62x0", "marvell,kirkwood-88f6281", "marvell,kirkwood";
memory {
device_type = "memory";
@@ -117,13 +117,13 @@
};
partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x600000>;
+ label = "second stage u-boot";
+ reg = <0x100000 0x200000>;
};
- partition@700000 {
- label = "root";
- reg = <0x0700000 0xf900000>;
+ partition@200000 {
+ label = "ubi";
+ reg = <0x200000 0xfe00000>;
};
};

@ -1,50 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-iconnect.dts
+++ b/arch/arm/boot/dts/kirkwood-iconnect.dts
@@ -15,8 +15,6 @@
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
stdout-path = &uart0;
- linux,initrd-start = <0x4500040>;
- linux,initrd-end = <0x4800000>;
};
ocp@f1000000 {
@@ -145,28 +143,23 @@
status = "okay";
partition@0 {
- label = "uboot";
- reg = <0x0000000 0xc0000>;
+ label = "u-boot";
+ reg = <0x0000000 0xe0000>;
};
- partition@a0000 {
- label = "env";
- reg = <0xa0000 0x20000>;
+ partition@e0000 {
+ label = "u-boot environment";
+ reg = <0xe0000 0x100000>;
};
partition@100000 {
- label = "zImage";
- reg = <0x100000 0x300000>;
+ label = "second stage u-boot";
+ reg = <0x100000 0x200000>;
};
- partition@540000 {
- label = "initrd";
- reg = <0x540000 0x300000>;
- };
-
- partition@980000 {
- label = "boot";
- reg = <0x980000 0x1f400000>;
+ partition@200000 {
+ label = "ubi";
+ reg = <0x200000 0x1fe00000>;
};
};

@ -1,32 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-dockstar.dts
+++ b/arch/arm/boot/dts/kirkwood-dockstar.dts
@@ -77,18 +77,22 @@
partition@0 {
label = "u-boot";
- reg = <0x0000000 0x100000>;
- read-only;
+ reg = <0x0000000 0xe0000>;
+ };
+
+ partition@e0000 {
+ label = "u-boot environment";
+ reg = <0xe0000 0x100000>;
};
partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
+ label = "second stage u-boot";
+ reg = <0x100000 0x200000>;
};
- partition@500000 {
- label = "data";
- reg = <0x0500000 0xfb00000>;
+ partition@200000 {
+ label = "ubi";
+ reg = <0x200000 0xfe00000>;
};
};

@ -1,33 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
+++ b/arch/arm/boot/dts/kirkwood-iomega_ix2_200.dts
@@ -185,18 +185,18 @@
};
partition@a0000 {
- label = "env";
+ label = "u-boot environment";
reg = <0xa0000 0x20000>;
read-only;
};
partition@100000 {
- label = "uImage";
+ label = "kernel";
reg = <0x100000 0x300000>;
};
partition@400000 {
- label = "rootfs";
+ label = "ubi";
reg = <0x400000 0x1C00000>;
};
};
@@ -210,7 +210,7 @@
};
&eth0 {
- status = "okay";
+ status = "disabled";
ethernet0-port@0 {
speed = <1000>;
duplex = <1>;

@ -1,258 +0,0 @@
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -220,6 +220,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-linkstation-lswsxl.dtb \
kirkwood-linkstation-lswvl.dtb \
kirkwood-linkstation-lswxl.dtb \
+ kirkwood-linksys-audi.dtb \
kirkwood-linksys-viper.dtb \
kirkwood-lschlv2.dtb \
kirkwood-lsxhl.dtb \
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts
@@ -0,0 +1,245 @@
+/*
+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500
+ *
+ * (c) 2013 Jonas Gorski <jogo@openwrt.org>
+ * (c) 2013 Deutsche Telekom Innovation Laboratories
+ * (c) 2014 Luka Perkov <luka@openwrt.org>
+ * (c) 2014 Dan Walters <dan@walters.io>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "Linksys Audi (EA3500)";
+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x4000000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >;
+ pinctrl-names = "default";
+
+ wps {
+ label = "WPS Button";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_green_power >;
+ pinctrl-names = "default";
+
+ green-power {
+ label = "audi:green:power";
+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ mvsw61xx {
+ compatible = "marvell,88e6171";
+ status = "okay";
+ reg = <0x10>;
+
+ mii-bus = <&mdio>;
+ cpu-port-0 = <5>;
+ cpu-port-1 = <6>;
+ is-indirect;
+ };
+
+ dsa {
+ compatible = "marvell,dsa";
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ dsa,ethernet = <&eth0port>;
+ dsa,mii-bus = <&mdio>;
+
+ switch@16,0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */
+
+ port@0 {
+ reg = <0>;
+ label = "ethernet1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "ethernet2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "ethernet3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "ethernet4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "internet";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ };
+ };
+ };
+};
+
+&pinctrl {
+ pmx_led_green_power: pmx-led-green-power {
+ marvell,pins = "mpp7";
+ marvell,function = "gpo";
+ };
+ pmx_btn_wps: pmx-btn-wps {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_btn_reset: pmx-btn-reset {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+};
+
+&nand {
+ status = "okay";
+ pinctrl-0 = <&pmx_nand>;
+ pinctrl-names = "default";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "u_env";
+ reg = <0x80000 0x4000>;
+ };
+
+ partition@84000 {
+ label = "s_env";
+ reg = <0x84000 0x4000>;
+ };
+
+ partition@200000 {
+ label = "kernel1";
+ reg = <0x200000 0x290000>;
+ };
+
+ partition@490000 {
+ label = "rootfs1";
+ reg = <0x490000 0x1170000>;
+ };
+
+ partition@1600000 {
+ label = "kernel2";
+ reg = <0x1600000 0x290000>;
+ };
+
+ partition@1890000 {
+ label = "rootfs2";
+ reg = <0x1890000 0x1170000>;
+ };
+
+ partition@2a00000 {
+ label = "syscfg";
+ reg = <0x2a00000 0x1600000>;
+ };
+
+ partition@88000 {
+ label = "unused";
+ reg = <0x88000 0x178000>;
+ };
+
+ };
+};
+
+&pciec {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set
+ * fixed speed and duplex.
+ */
+&eth0 {
+ status = "okay";
+ ethernet0-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+/* eth1 is connected to the switch at port 6. However DSA only supports a
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
+ */
+&eth1 {
+ status = "okay";
+ ethernet1-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
+
+/* There is no battery on the board, so the RTC does not keep
+ * time when there is no power, making it useless.
+ */
+&rtc {
+ status = "disabled";
+};

@ -1,64 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
@@ -69,6 +69,17 @@
};
};
+ mvsw61xx {
+ compatible = "marvell,88e6171";
+ status = "okay";
+ reg = <0x10>;
+
+ mii-bus = <&mdio>;
+ cpu-port-0 = <5>;
+ cpu-port-1 = <6>;
+ is-indirect;
+ };
+
dsa {
compatible = "marvell,dsa";
#address-cells = <2>;
@@ -161,22 +172,22 @@
};
partition@200000 {
- label = "kernel";
+ label = "kernel1";
reg = <0x200000 0x2A0000>;
};
partition@4A0000 {
- label = "rootfs";
+ label = "rootfs1";
reg = <0x4A0000 0x1760000>;
};
partition@1C00000 {
- label = "alt_kernel";
+ label = "kernel2";
reg = <0x1C00000 0x2A0000>;
};
partition@1EA0000 {
- label = "alt_rootfs";
+ label = "rootfs2";
reg = <0x1EA0000 0x1760000>;
};
@@ -225,10 +236,14 @@
};
/* eth1 is connected to the switch at port 6. However DSA only supports a
- * single CPU port. So leave this port disabled to avoid confusion.
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
*/
&eth1 {
- status = "disabled";
+ status = "okay";
+ ethernet1-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
};
/* There is no battery on the board, so the RTC does not keep

@ -1,130 +0,0 @@
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -207,6 +207,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-ds411.dtb \
kirkwood-ds411j.dtb \
kirkwood-ds411slim.dtb \
+ kirkwood-goflexhome.dtb \
kirkwood-goflexnet.dtb \
kirkwood-guruplug-server-plus.dtb \
kirkwood-ib62x0.dtb \
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts
@@ -0,0 +1,117 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+ model = "Seagate GoFlex Home";
+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pmx_usb_power_enable: pmx-usb-power-enable {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_led_white: pmx-led-white {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_led_green: pmx-led_green {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_led_orange: pmx-led-orange {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ };
+ serial@12000 {
+ status = "ok";
+ };
+
+ sata@80000 {
+ status = "okay";
+ nr-ports = <2>;
+ };
+
+ };
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ health {
+ label = "status:green:health";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "default-on";
+ };
+ fault {
+ label = "status:orange:fault";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ misc {
+ label = "status:white:misc";
+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_usb_power_enable>;
+ pinctrl-names = "default";
+
+ usb_power: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&nand {
+ chip-delay = <40>;
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0000000 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "ubi";
+ reg = <0x100000 0x0ff00000>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&eth0 {
+ status = "okay";
+ ethernet0-port@0 {
+ phy-handle = <&ethphy0>;
+ };
+};

@ -1,23 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-goflexnet.dts
+++ b/arch/arm/boot/dts/kirkwood-goflexnet.dts
@@ -158,18 +158,8 @@
};
partition@100000 {
- label = "uImage";
- reg = <0x0100000 0x400000>;
- };
-
- partition@500000 {
- label = "pogoplug";
- reg = <0x0500000 0x2000000>;
- };
-
- partition@2500000 {
- label = "root";
- reg = <0x02500000 0xd800000>;
+ label = "ubi";
+ reg = <0x0100000 0x0ff00000>;
};
};

@ -1,48 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
+++ b/arch/arm/boot/dts/kirkwood-nsa3x0-common.dtsi
@@ -111,40 +111,16 @@
partition@0 {
label = "uboot";
- reg = <0x0000000 0x0100000>;
+ reg = <0x0000000 0x00c0000>;
read-only;
};
partition@100000 {
label = "uboot_env";
- reg = <0x0100000 0x0080000>;
+ reg = <0x00c0000 0x0080000>;
};
- partition@180000 {
- label = "key_store";
- reg = <0x0180000 0x0080000>;
- };
- partition@200000 {
- label = "info";
- reg = <0x0200000 0x0080000>;
- };
- partition@280000 {
- label = "etc";
- reg = <0x0280000 0x0a00000>;
- };
- partition@c80000 {
- label = "kernel_1";
- reg = <0x0c80000 0x0a00000>;
- };
- partition@1680000 {
- label = "rootfs1";
- reg = <0x1680000 0x2fc0000>;
- };
- partition@4640000 {
- label = "kernel_2";
- reg = <0x4640000 0x0a00000>;
- };
- partition@5040000 {
- label = "rootfs2";
- reg = <0x5040000 0x2fc0000>;
+ partition@140000 {
+ label = "ubi";
+ reg = <0x0140000 0x7ec0000>;
};
};

@ -1,147 +0,0 @@
kirkwood: add nsa310b dtb, a zyxel nsa310 variant
add support to a nsa310 variant with red/green usb led
and lm85 temp/fan controller
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
NOTE: this patch can be upstreamed as-is, LEDE-specific
nand partitions are set in another patch
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -238,6 +238,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-ns2mini.dtb \
kirkwood-nsa310.dtb \
kirkwood-nsa310a.dtb \
+ kirkwood-nsa310b.dtb \
kirkwood-nsa320.dtb \
kirkwood-nsa325.dtb \
kirkwood-openblocks_a6.dtb \
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts
@@ -0,0 +1,124 @@
+/dts-v1/;
+
+#include "kirkwood-nsa3x0-common.dtsi"
+
+/*
+ * There are at least two different NSA310 designs. This variant has
+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller.
+ */
+
+/ {
+ model = "ZyXEL NSA310b";
+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart0;
+ };
+
+ ocp@f1000000 {
+ pinctrl: pin-controller@10000 {
+ pinctrl-names = "default";
+
+ pmx_led_esata_green: pmx-led-esata-green {
+ marvell,pins = "mpp12";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_esata_red: pmx-led-esata-red {
+ marvell,pins = "mpp13";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_green: pmx-led-usb-green {
+ marvell,pins = "mpp15";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_usb_red: pmx-led-usb-red {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_green: pmx-led-sys-green {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_sys_red: pmx-led-sys-red {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd_green: pmx-led-hdd-green {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_hdd_red: pmx-led-hdd-red {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+
+ };
+
+ i2c@11000 {
+ status = "okay";
+
+ lm85: lm85@2e {
+ compatible = "national,lm85";
+ reg = <0x2e>;
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ green-sys {
+ label = "nsa310:green:sys";
+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ };
+ red-sys {
+ label = "nsa310:red:sys";
+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ green-hdd {
+ label = "nsa310:green:hdd";
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ };
+ red-hdd {
+ label = "nsa310:red:hdd";
+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+ };
+ green-esata {
+ label = "nsa310:green:esata";
+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+ };
+ red-esata {
+ label = "nsa310:red:esata";
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ };
+ green-usb {
+ label = "nsa310:green:usb";
+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ };
+ red-usb {
+ label = "nsa310:red:usb";
+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
+ };
+ green-copy {
+ label = "nsa310:green:copy";
+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+ red-copy {
+ label = "nsa310:red:copy";
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};

@ -1,173 +0,0 @@
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-on100.dts
@@ -0,0 +1,160 @@
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6282.dtsi"
+
+/ {
+ model = "Cisco Systems ON100";
+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x20000000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_btn_reset>;
+ pinctrl-names = "default";
+
+ button@1 {
+ label = "Reset Button";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >;
+ pinctrl-names = "default";
+
+ health-g {
+ label = "on100:green:health";
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ };
+
+ health-r {
+ label = "on100:red:health";
+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+
+ health2-g {
+ label = "on100:green:health2";
+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+ };
+
+ health2-r {
+ label = "on100:red:health2";
+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&eth0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ phy-handle = <&ethphy0>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+&eth1 {
+ status = "okay";
+
+ ethernet1-port@0 {
+ phy-handle = <&ethphy1>;
+ phy-connection-type = "rgmii-id";
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy0: ethernet-phy@0 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ /* Marvell 88E1121R */
+ compatible = "ethernet-phy-id0141.0cb0",
+ "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&nand {
+ status = "okay";
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x00000000 0x000a0000>;
+ read-only;
+ };
+
+ partition@a0000 {
+ label = "u-boot environment";
+ reg = <0x000a0000 0x00020000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "kernel";
+ reg = <0x000c0000 0x00540000>;
+ };
+
+ partition@600000 {
+ label = "ubi";
+ reg = <0x00600000 0x1fa00000>;
+ };
+};
+
+&pinctrl {
+ pmx_led_health_r: pmx-led-health-r {
+ marvell,pins = "mpp45";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health_g: pmx-led-health-g {
+ marvell,pins = "mpp44";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health2_r: pmx-led-health2-r {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+
+ pmx_led_health2_g: pmx-led-health2-g {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+
+ pmx_btn_reset: pmx-led-reset {
+ marvell,pins = "mpp31";
+ marvell,function = "gpio";
+ };
+};
+
+&sdio {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -241,6 +241,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-nsa310b.dtb \
kirkwood-nsa320.dtb \
kirkwood-nsa325.dtb \
+ kirkwood-on100.dtb \
kirkwood-openblocks_a6.dtb \
kirkwood-openblocks_a7.dtb \
kirkwood-openrd-base.dtb \

@ -1,59 +0,0 @@
--- a/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
+++ b/arch/arm/boot/dts/kirkwood-pogoplug-series-4.dts
@@ -23,6 +23,7 @@
};
chosen {
+ bootargs = "console=ttyS0,115200";
stdout-path = "uart0:115200n8";
};
@@ -36,8 +37,8 @@
eject {
debounce_interval = <50>;
wakeup-source;
- linux,code = <KEY_EJECTCD>;
- label = "Eject Button";
+ linux,code = <KEY_RESTART>;
+ label = "Reset";
gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
};
};
@@ -136,29 +137,19 @@
#size-cells = <1>;
partition@0 {
- label = "u-boot";
- reg = <0x00000000 0x200000>;
+ label = "uboot";
+ reg = <0x00000000 0x1c0000>;
read-only;
};
- partition@200000 {
- label = "uImage";
- reg = <0x00200000 0x300000>;
- };
-
- partition@500000 {
- label = "uImage2";
- reg = <0x00500000 0x300000>;
+ partition@1c0000 {
+ label = "uboot_env";
+ reg = <0x001c0000 0x40000>;
};
- partition@800000 {
- label = "failsafe";
- reg = <0x00800000 0x800000>;
- };
-
- partition@1000000 {
- label = "root";
- reg = <0x01000000 0x7000000>;
+ partition@200000 {
+ label = "ubi";
+ reg = <0x00200000 0x7e00000>;
};
};
};

@ -1,35 +0,0 @@
From: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Subject: [PATCH] net: mv643xx_eth: Make TSO disabled by default
Data corruption has been observed to be produced by TSO. For instance,
accessing files on a NFS-server with TSO enabled results in different data
transferred each time.
This has been observed only on Kirkwood platforms, i.e. with the mv643xx_eth
driver. Same tests on platforms using the mvneta ethernet driver have
passed without errors.
Make TSO disabled by default for now, until we can found a proper fix
for the regression.
Fixes: 3ae8f4e0b98 ('net: mv643xx_eth: Implement software TSO')
Reported-by: Slawomir Gajzner <slawomir.gajzner <at> gmail.com>
Reported-by: Julien D'Ascenzio <jdascenzio <at> yahoo.fr>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia <at> free-electrons.com>
---
--- a/drivers/net/ethernet/marvell/mv643xx_eth.c
+++ b/drivers/net/ethernet/marvell/mv643xx_eth.c
@@ -3197,11 +3197,11 @@ static int mv643xx_eth_probe(struct plat
dev->watchdog_timeo = 2 * HZ;
dev->base_addr = 0;
- dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO;
+ dev->features = NETIF_F_SG | NETIF_F_IP_CSUM;
dev->vlan_features = dev->features;
dev->features |= NETIF_F_RXCSUM;
- dev->hw_features = dev->features;
+ dev->hw_features = dev->features | NETIF_F_TSO;
dev->priv_flags |= IFF_UNICAST_FLT;
dev->gso_max_segs = MV643XX_MAX_TSO_SEGS;

@ -1,10 +0,0 @@
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -117,6 +117,7 @@ config MACH_DOVE
config MACH_KIRKWOOD
bool "Marvell Kirkwood boards"
depends on ARCH_MULTI_V5
+ select ARCH_WANT_LIBATA_LEDS
select CPU_FEROCEON
select GPIOLIB
select KIRKWOOD_CLK

@ -1,62 +0,0 @@
The WRT1900AC among other Linksys routers uses a dual-firmware layout.
Dynamically rename the active partition to "ubi".
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
---
--- a/drivers/mtd/ofpart.c
+++ b/drivers/mtd/ofpart.c
@@ -25,6 +25,8 @@ static bool node_has_compatible(struct d
return of_get_property(pp, "compatible", NULL);
}
+static int mangled_rootblock;
+
static int parse_fixed_partitions(struct mtd_info *master,
const struct mtd_partition **pparts,
struct mtd_part_parser_data *data)
@@ -32,6 +34,7 @@ static int parse_fixed_partitions(struct
struct mtd_partition *parts;
struct device_node *mtd_node;
struct device_node *ofpart_node;
+ const char *owrtpart = "ubi";
const char *partname;
struct device_node *pp;
int nr_parts, i, ret = 0;
@@ -110,9 +113,15 @@ static int parse_fixed_partitions(struct
parts[i].size = of_read_number(reg + a_cells, s_cells);
parts[i].of_node = pp;
- partname = of_get_property(pp, "label", &len);
- if (!partname)
- partname = of_get_property(pp, "name", &len);
+ if (mangled_rootblock && (i == mangled_rootblock)) {
+ partname = owrtpart;
+ } else {
+ partname = of_get_property(pp, "label", &len);
+
+ if (!partname)
+ partname = of_get_property(pp, "name", &len);
+ }
+
parts[i].name = partname;
if (of_get_property(pp, "read-only", &len))
@@ -220,6 +229,18 @@ static int __init ofpart_parser_init(voi
return 0;
}
+static int __init active_root(char *str)
+{
+ get_option(&str, &mangled_rootblock);
+
+ if (!mangled_rootblock)
+ return 1;
+
+ return 1;
+}
+
+__setup("mangled_rootblock=", active_root);
+
static void __exit ofpart_parser_exit(void)
{
deregister_mtd_parser(&ofpart_parser);
Loading…
Cancel
Save