ramips: add support for Skylab SKW92A in EVB

Specifically, SKW92A_E16, described here:

  http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf

Specification:
- MediaTek MT7628N/N (580 Mhz)
- 64 MB of RAM
- 16 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x u.FL
- Power by micro-USB connector at USB1 on EVB
- UART via micro-USB connector at USB3 on EVB (57600 8n1)
- 5x Ethernet LEDs
- 1x WLAN LEDs
- 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next
  to daughter board on EVB
- WPS/Reset button (S2 on EVB)
- RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board

Flash instruction:

>From Skylab firmware:

1. Associate with SKYLAP_AP
2. In a browser, load: http://10.10.10.254/
3. Username/password: admin/admin
4. In web admin interface: Administration / Upload Firmware, browse to
   sysupgrade image, apply, flash will fail with a message:
   Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data!
5. Telnet to 10.10.10.254, drops you into a root shell with no credentials
6. # cd /var
7. # mtd_write -r write tmpFW mtd4
   Unlocking mtd4 ...
   Writing from tmpFW to mtd4 ... [e]
8. When flash has completed, you will have booted into your firmware.

>From U-boot via TFTP and initramfs:

1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server
2. Connect to serial console at USB3 on EVB
3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "1"
7. At u-boot prompts:
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin
8. Move ethernet to port 0 (WAN) on EVB
9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash
   with sysupgrade.

>From U-boot via TFTP direct flash:

1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server
2. Connect to serial console at USB3 on EVB (57600 8N1)
3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g.
   192.168.11.20)
4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC
5. Apply power to EVB
6. Interrupt u-boot with keypress of "2"
7. At u-boot prompts:
   Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y
   Input device IP (10.10.10.123) ==:192.168.11.21
   Input server IP (10.10.10.3) ==:192.168.11.20
   Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin
8. When transfer is complete or as OpenWrt begins booting, move ethernet to
   port 0 (WAN).

Signed-off-by: Russell Senior <russell@personaltelco.net>
master
Russell Senior 6 years ago committed by John Crispin
parent 0331770299
commit e42327aa89
  1. 3
      target/linux/ramips/base-files/etc/board.d/01_leds
  2. 8
      target/linux/ramips/base-files/etc/board.d/02_network
  3. 3
      target/linux/ramips/base-files/lib/ramips.sh
  4. 1
      target/linux/ramips/base-files/lib/upgrade/platform.sh
  5. 120
      target/linux/ramips/dts/SKW92A.dts
  6. 8
      target/linux/ramips/image/mt76x8.mk

@ -283,6 +283,9 @@ rt-n14u)
ucidef_set_led_netdev "wan" "wan" "$boardname:blue:wan" eth0.2
set_wifi_led "$boardname:blue:air"
;;
skw92a)
set_wifi_led "$boardname:green:wlan"
;;
tama,w06)
ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0"
ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt"

@ -345,6 +345,10 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
;;
skw92a)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0"
;;
tew-638apb-v2)
ucidef_add_switch "switch0" \
"4:lan" "6@eth0"
@ -554,6 +558,10 @@ ramips_setup_macs()
lan_mac=$(macaddr_setbit_la "$lan_mac")
wan_mac=$(mtd_get_mac_binary factory 32772)
;;
skw92a)
lan_mac=$(mtd_get_mac_binary factory 40)
wan_mac=$(mtd_get_mac_binary factory 46)
;;
tew-691gr)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3)
;;

@ -472,6 +472,9 @@ ramips_board_detect() {
*"SAP-G3200U3")
name="sap-g3200u3"
;;
*"SKW92A")
name="skw92a"
;;
*"SL-R7205"*)
name="sl-r7205"
;;

@ -151,6 +151,7 @@ platform_check_image() {
rut5xx|\
sap-g3200u3|\
sk-wb8|\
skw92a|\
sl-r7205|\
tama,w06|\
tew-638apb-v2|\

@ -0,0 +1,120 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "mt7628an.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/{
compatible = "skylab,skw92a", "mediatek,mt7628an-soc";
model = "SKW92A";
aliases {
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_power;
};
chosen {
bootargs = "console=ttyS0,57600";
};
memory@0 {
device_type = "memory";
reg = <0x0 0x4000000>;
};
gpio-leds {
compatible = "gpio-leds";
led_power: wps {
label = "skw92:green:wps";
gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
};
};
gpio-keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
};
};
&pinctrl {
state_default: pinctrl0 {
gpio {
ralink,group = "wdt", "refclk", "gpio";
ralink,function = "gpio";
};
};
};
&ethernet {
mtd-mac-address = <&factory 0x28>;
};
&wmac {
status = "okay";
ralink,mtd-eeprom = <&factory 0x0>;
};
&spi0 {
status = "okay";
m25p80@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <10000000>;
m25p,chunked-io = <32>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x0 0x30000>;
read-only;
};
partition@30000 {
label = "u-boot-env";
reg = <0x30000 0x10000>;
read-only;
};
factory: partition@40000 {
label = "factory";
reg = <0x40000 0x10000>;
read-only;
};
partition@50000 {
label = "firmware";
reg = <0x50000 0xfb0000>;
compatible = "denx,uimage";
};
};
};
};
&uart1 {
status = "okay";
};
&ehci {
status = "okay";
};
&ohci {
status = "okay";
};

@ -150,6 +150,14 @@ define Device/pbr-d1
endef
TARGET_DEVICES += pbr-d1
define Device/skw92a
DTS := SKW92A
IMAGE_SIZE := 16064k
DEVICE_TITLE := Skylab SKW92A
DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci
endef
TARGET_DEVICES += skw92a
define Device/tplink_tl-wa801nd-v5
$(Device/tplink)
DTS := TL-WA801NDV5

Loading…
Cancel
Save