Move NAND driver from rb1xx to adm5120, rbmipsnand fixed by David Goodenough, thanks !

SVN-Revision: 6991
master
Florian Fainelli 18 years ago
parent 29300267d3
commit d22c77b808
  1. 20
      target/linux/adm5120-2.6/config/default
  2. 111
      target/linux/adm5120-2.6/files/drivers/mtd/nand/rbmipsnand.c
  3. 29
      target/linux/adm5120-2.6/patches/500-Nand.patch

@ -138,7 +138,7 @@ CONFIG_MTD=y
# CONFIG_MTD_ABSENT is not set
CONFIG_MTD_ADM5120=y
CONFIG_MTD_BLOCK=y
# CONFIG_MTD_BLOCK2MTD is not set
CONFIG_MTD_BLOCK2MTD=y
CONFIG_MTD_CFI=y
# CONFIG_MTD_CFI_ADV_OPTIONS is not set
CONFIG_MTD_CFI_AMDSTD=y
@ -168,6 +168,13 @@ CONFIG_MTD_MAP_BANK_WIDTH_4=y
# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
# CONFIG_MTD_MTDRAM is not set
CONFIG_MTD_MYLOADER_PARTS=y
CONFIG_MTD_NAND=y
# CONFIG_MTD_NAND_DISKONCHIP is not set
# CONFIG_MTD_NAND_ECC_SMC is not set
CONFIG_MTD_NAND_IDS=y
# CONFIG_MTD_NAND_NANDSIM is not set
CONFIG_MTD_NAND_RB100=y
# CONFIG_MTD_NAND_VERIFY_WRITE is not set
# CONFIG_MTD_OBSOLETE_CHIPS is not set
# CONFIG_MTD_ONENAND is not set
CONFIG_MTD_PARTITIONS=y
@ -178,7 +185,6 @@ CONFIG_MTD_PARTITIONS=y
# CONFIG_MTD_PMC551 is not set
# CONFIG_MTD_RAM is not set
# CONFIG_MTD_REDBOOT_PARTS is not set
CONFIG_MTD_MYLOADER_PARTS=y
# CONFIG_MTD_ROM is not set
# CONFIG_MTD_SLRAM is not set
CONFIG_NETFILTER_XT_MATCH_QUOTA=m
@ -233,6 +239,7 @@ CONFIG_SYN_COOKIES=y
CONFIG_SYS_HAS_CPU_MIPS32_R1=y
CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y
CONFIG_SYS_SUPPORTS_ARBIT_HZ=y
CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y
CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y
CONFIG_TMPFS_POSIX_ACL=y
# CONFIG_TOSHIBA_JMR3927 is not set
@ -259,4 +266,13 @@ CONFIG_USB_ADM5120_HCD=y
# CONFIG_USB_USBNET_MII is not set
# CONFIG_USB_ZD1201 is not set
CONFIG_VM_EVENT_COUNTERS=y
# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set
CONFIG_YAFFS_AUTO_YAFFS2=y
# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set
# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set
# CONFIG_YAFFS_DOES_ECC is not set
CONFIG_YAFFS_FS=y
CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y
CONFIG_YAFFS_YAFFS1=y
CONFIG_YAFFS_YAFFS2=y
# CONFIG_ZD1211RW is not set

@ -0,0 +1,111 @@
/*==============================================================================*/
/* rbmipsnand.c */
/* This module is derived from the 2.4 driver shipped by Microtik for their */
/* Routerboard 1xx and 5xx series boards. It provides support for the built in */
/* NAND flash on the Routerboard 1xx series boards for Linux 2.6.19+. */
/* Licence: Original Microtik code seems not to have a licence. */
/* Rewritten code all GPL V2. */
/* Copyright(C) 2007 david.goodenough@linkchoose.co.uk (for rewriten code) */
/*==============================================================================*/
#include <linux/init.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/delay.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/bootinfo.h>
#define SMEM1_BASE 0x10000000 // from ADM5120 documentation
#define SMEM1(x) (*((volatile unsigned char *) (KSEG1ADDR(SMEM1_BASE) + x)))
#define NAND_RW_REG 0x0 //data register
#define NAND_SET_CEn 0x1 //CE# low
#define NAND_CLR_CEn 0x2 //CE# high
#define NAND_CLR_CLE 0x3 //CLE low
#define NAND_SET_CLE 0x4 //CLE high
#define NAND_CLR_ALE 0x5 //ALE low
#define NAND_SET_ALE 0x6 //ALE high
#define NAND_SET_SPn 0x7 //SP# low (use spare area)
#define NAND_CLR_SPn 0x8 //SP# high (do not use spare area)
#define NAND_SET_WPn 0x9 //WP# low
#define NAND_CLR_WPn 0xA //WP# high
#define NAND_STS_REG 0xB //Status register
#define MEM32(x) *((volatile unsigned *) (x))
static void __iomem *p_nand;
static int rb100_dev_ready(struct mtd_info *mtd) {
return SMEM1(NAND_STS_REG) & 0x80;
}
static void rbmips_hwcontrol100(struct mtd_info *mtd, int cmd, unsigned int ctrl) {
struct nand_chip *chip = mtd->priv;
if (ctrl & NAND_CTRL_CHANGE) {
SMEM1((( ctrl & NAND_CLE) ? NAND_SET_CLE : NAND_CLR_CLE)) = 0x01;
SMEM1((( ctrl & NAND_ALE) ? NAND_SET_ALE : NAND_CLR_ALE)) = 0x01;
SMEM1((( ctrl & NAND_NCE) ? NAND_SET_CEn : NAND_CLR_CEn)) = 0x01;
}
if( cmd != NAND_CMD_NONE)
writeb( cmd, chip->IO_ADDR_W);
}
static struct mtd_partition partition_info[] = {
{
name: "RouterBoard NAND Boot",
offset: 0,
size: 4 * 1024 * 1024
},
{
name: "RouterBoard NAND Main",
offset: MTDPART_OFS_NXTBLK,
size: MTDPART_SIZ_FULL
}
};
static struct mtd_info rmtd;
static struct nand_chip rnand;
static unsigned init_ok = 0;
unsigned get_rbnand_block_size(void) {
return init_ok ? rmtd.writesize : 0;
}
EXPORT_SYMBOL(get_rbnand_block_size);
int __init rbmips_init(void) {
memset(&rmtd, 0, sizeof(rmtd));
memset(&rnand, 0, sizeof(rnand));
printk("RB1xx nand\n");
MEM32(0xB2000064) = 0x100;
MEM32(0xB2000008) = 0x1;
SMEM1(NAND_SET_SPn) = 0x01;
SMEM1(NAND_CLR_WPn) = 0x01;
rnand.IO_ADDR_R = (unsigned char *)KSEG1ADDR(SMEM1_BASE);
rnand.IO_ADDR_W = rnand.IO_ADDR_R;
rnand.cmd_ctrl = rbmips_hwcontrol100;
rnand.dev_ready = rb100_dev_ready;
p_nand = (void __iomem *)ioremap(( unsigned long)SMEM1_BASE, 0x1000);
if (!p_nand) {
printk("RB1xx nand Unable ioremap buffer");
return -ENXIO;
}
rnand.ecc.mode = NAND_ECC_SOFT;
rnand.chip_delay = 25;
rnand.options |= NAND_NO_AUTOINCR;
rmtd.priv = &rnand;
if (nand_scan(&rmtd, 1) && nand_scan(&rmtd, 1)
&& nand_scan(&rmtd, 1) && nand_scan(&rmtd, 1)) {
printk("RB1xxx nand device not found");
iounmap ((void *)p_nand);
return -ENXIO;
}
add_mtd_partitions(&rmtd, partition_info, 2);
init_ok = 1;
return 0;
}
module_init(rbmips_init);

@ -0,0 +1,29 @@
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index cfe288a..c528024 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -55,6 +55,12 @@ config MTD_NAND_TOTO
help
Support for NAND flash on Texas Instruments Toto platform.
+config MTD_NAND_RB100
+ tristate "NAND Flash device on RB100 board"
+ depends on MTD_NAND
+ help
+ Support for NAND flash on RB100 platform.
+
config MTD_NAND_IDS
tristate
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 4174202..2be57c1 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_MTD_NAND_IDS) += nand_ids.
obj-$(CONFIG_MTD_NAND_SPIA) += spia.o
obj-$(CONFIG_MTD_NAND_TOTO) += toto.o
+obj-$(CONFIG_MTD_NAND_RB100) += rbmipsnand.o
obj-$(CONFIG_MTD_NAND_AUTCPU12) += autcpu12.o
obj-$(CONFIG_MTD_NAND_EDB7312) += edb7312.o
obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o
Loading…
Cancel
Save