This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>master
Sebastian Quilitz
8 years ago
committed by
Mathias Kresin
parent
0e7869f204
commit
ae79c41286
@ -0,0 +1,423 @@ |
||||
#include "qcom-ipq8064-v1.0.dtsi" |
||||
|
||||
#include <dt-bindings/input/input.h> |
||||
|
||||
/ { |
||||
model = "TP-Link Archer VR2600v"; |
||||
compatible = "tplink,vr2600v", "qcom,ipq8064"; |
||||
|
||||
memory@0 { |
||||
reg = <0x42000000 0x1e000000>; |
||||
device_type = "memory"; |
||||
}; |
||||
|
||||
reserved-memory { |
||||
#address-cells = <1>; |
||||
#size-cells = <1>; |
||||
ranges; |
||||
rsvd@41200000 { |
||||
reg = <0x41200000 0x300000>; |
||||
no-map; |
||||
}; |
||||
}; |
||||
|
||||
aliases { |
||||
serial0 = &uart4; |
||||
mdio-gpio0 = &mdio0; |
||||
|
||||
led-boot = &power; |
||||
led-failsafe = &general; |
||||
led-running = &power; |
||||
led-upgrade = &general; |
||||
}; |
||||
|
||||
chosen { |
||||
linux,stdout-path = "serial0:115200n8"; |
||||
}; |
||||
|
||||
soc { |
||||
pinmux@800000 { |
||||
led_pins: led_pins { |
||||
pins = "gpio7", "gpio8", "gpio9", "gpio16", "gpio17", |
||||
"gpio26", "gpio53", "gpio56", "gpio66"; |
||||
function = "gpio"; |
||||
drive-strength = <2>; |
||||
bias-pull-up; |
||||
}; |
||||
|
||||
i2c4_pins: i2c4_pinmux { |
||||
mux { |
||||
pins = "gpio12", "gpio13"; |
||||
function = "gsbi4"; |
||||
drive-strength = <12>; |
||||
bias-disable; |
||||
}; |
||||
}; |
||||
|
||||
button_pins: button_pins { |
||||
pins = "gpio54", "gpio64", "gpio65", "gpio67", "gpio68"; |
||||
function = "gpio"; |
||||
drive-strength = <2>; |
||||
bias-pull-up; |
||||
}; |
||||
|
||||
spi_pins: spi_pins { |
||||
mux { |
||||
pins = "gpio18", "gpio19", "gpio21"; |
||||
function = "gsbi5"; |
||||
bias-pull-down; |
||||
}; |
||||
|
||||
data { |
||||
pins = "gpio18", "gpio19"; |
||||
drive-strength = <10>; |
||||
}; |
||||
|
||||
cs { |
||||
pins = "gpio20"; |
||||
drive-strength = <10>; |
||||
bias-pull-up; |
||||
}; |
||||
|
||||
clk { |
||||
pins = "gpio21"; |
||||
drive-strength = <12>; |
||||
}; |
||||
}; |
||||
|
||||
mdio0_pins: mdio0_pins { |
||||
mux { |
||||
pins = "gpio0", "gpio1"; |
||||
function = "gpio"; |
||||
drive-strength = <8>; |
||||
bias-disable; |
||||
}; |
||||
}; |
||||
|
||||
rgmii2_pins: rgmii2_pins { |
||||
mux { |
||||
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32", |
||||
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ; |
||||
function = "rgmii2"; |
||||
drive-strength = <8>; |
||||
bias-disable; |
||||
}; |
||||
}; |
||||
|
||||
}; |
||||
|
||||
gsbi@16300000 { |
||||
qcom,mode = <GSBI_PROT_I2C_UART>; |
||||
status = "ok"; |
||||
serial@16340000 { |
||||
status = "ok"; |
||||
}; |
||||
/* |
||||
* The i2c device on gsbi4 should not be enabled. |
||||
* On ipq806x designs gsbi4 i2c is meant for exclusive |
||||
* RPM usage. Turning this on in kernel manifests as |
||||
* i2c failure for the RPM. |
||||
*/ |
||||
}; |
||||
|
||||
gsbi5: gsbi@1a200000 { |
||||
qcom,mode = <GSBI_PROT_SPI>; |
||||
status = "ok"; |
||||
|
||||
spi4: spi@1a280000 { |
||||
status = "ok"; |
||||
spi-max-frequency = <50000000>; |
||||
|
||||
pinctrl-0 = <&spi_pins>; |
||||
pinctrl-names = "default"; |
||||
|
||||
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>; |
||||
|
||||
flash: W25Q128@0 { |
||||
compatible = "jedec,spi-nor"; |
||||
#address-cells = <1>; |
||||
#size-cells = <1>; |
||||
spi-max-frequency = <50000000>; |
||||
reg = <0>; |
||||
|
||||
SBL1@0 { |
||||
label = "SBL1"; |
||||
reg = <0x0 0x20000>; |
||||
read-only; |
||||
}; |
||||
|
||||
MIBIB@20000 { |
||||
label = "MIBIB"; |
||||
reg = <0x20000 0x20000>; |
||||
read-only; |
||||
}; |
||||
|
||||
SBL2@40000 { |
||||
label = "SBL2"; |
||||
reg = <0x40000 0x40000>; |
||||
read-only; |
||||
}; |
||||
|
||||
SBL3@80000 { |
||||
label = "SBL3"; |
||||
reg = <0x80000 0x80000>; |
||||
read-only; |
||||
}; |
||||
|
||||
DDRCONFIG@100000 { |
||||
label = "DDRCONFIG"; |
||||
reg = <0x100000 0x10000>; |
||||
read-only; |
||||
}; |
||||
|
||||
SSD@110000 { |
||||
label = "SSD"; |
||||
reg = <0x110000 0x10000>; |
||||
read-only; |
||||
}; |
||||
|
||||
TZ@120000 { |
||||
label = "TZ"; |
||||
reg = <0x120000 0x80000>; |
||||
read-only; |
||||
}; |
||||
|
||||
RPM@1a0000 { |
||||
label = "RPM"; |
||||
reg = <0x1a0000 0x80000>; |
||||
read-only; |
||||
}; |
||||
|
||||
APPSBL@220000 { |
||||
label = "APPSBL"; |
||||
reg = <0x220000 0x80000>; |
||||
read-only; |
||||
}; |
||||
|
||||
APPSBLENV@2a0000 { |
||||
label = "APPSBLENV"; |
||||
reg = <0x2a0000 0x40000>; |
||||
read-only; |
||||
}; |
||||
|
||||
OLDART@2e0000 { |
||||
label = "OLDART"; |
||||
reg = <0x2e0000 0x40000>; |
||||
read-only; |
||||
}; |
||||
|
||||
kernel@320000 { |
||||
label = "kernel"; |
||||
reg = <0x320000 0x200000>; |
||||
}; |
||||
|
||||
rootfs@520000 { |
||||
label = "rootfs"; |
||||
reg = <0x520000 0xa60000>; |
||||
}; |
||||
|
||||
defaultmac: default-mac@0xfaf100 { |
||||
label = "default-mac"; |
||||
reg = <0xfaf100 0x00200>; |
||||
read-only; |
||||
}; |
||||
|
||||
ART@fc0000 { |
||||
label = "ART"; |
||||
reg = <0xfc0000 0x40000>; |
||||
read-only; |
||||
}; |
||||
|
||||
}; |
||||
}; |
||||
}; |
||||
|
||||
phy@100f8800 { /* USB3 port 1 HS phy */ |
||||
status = "ok"; |
||||
}; |
||||
|
||||
phy@100f8830 { /* USB3 port 1 SS phy */ |
||||
status = "ok"; |
||||
}; |
||||
|
||||
phy@110f8800 { /* USB3 port 0 HS phy */ |
||||
status = "ok"; |
||||
}; |
||||
|
||||
phy@110f8830 { /* USB3 port 0 SS phy */ |
||||
status = "ok"; |
||||
}; |
||||
|
||||
usb30@0 { |
||||
status = "ok"; |
||||
}; |
||||
|
||||
usb30@1 { |
||||
status = "ok"; |
||||
}; |
||||
|
||||
pcie0: pci@1b500000 { |
||||
status = "ok"; |
||||
phy-tx0-term-offset = <7>; |
||||
}; |
||||
|
||||
pcie1: pci@1b700000 { |
||||
status = "ok"; |
||||
phy-tx0-term-offset = <7>; |
||||
}; |
||||
|
||||
mdio0: mdio { |
||||
compatible = "virtual,mdio-gpio"; |
||||
#address-cells = <1>; |
||||
#size-cells = <0>; |
||||
gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>; |
||||
pinctrl-0 = <&mdio0_pins>; |
||||
pinctrl-names = "default"; |
||||
|
||||
phy0: ethernet-phy@0 { |
||||
device_type = "ethernet-phy"; |
||||
reg = <0>; |
||||
qca,ar8327-initvals = < |
||||
0x00004 0x7600000 /* PAD0_MODE */ |
||||
0x00008 0x1000000 /* PAD5_MODE */ |
||||
0x0000c 0x80 /* PAD6_MODE */ |
||||
0x000e4 0x6a545 /* MAC_POWER_SEL */ |
||||
0x000e0 0xc74164de /* SGMII_CTRL */ |
||||
0x0007c 0x4e /* PORT0_STATUS */ |
||||
0x00094 0x4e /* PORT6_STATUS */ |
||||
>; |
||||
}; |
||||
|
||||
phy4: ethernet-phy@4 { |
||||
device_type = "ethernet-phy"; |
||||
reg = <4>; |
||||
}; |
||||
}; |
||||
|
||||
gmac1: ethernet@37200000 { |
||||
status = "ok"; |
||||
phy-mode = "rgmii"; |
||||
qcom,id = <1>; |
||||
|
||||
pinctrl-0 = <&rgmii2_pins>; |
||||
pinctrl-names = "default"; |
||||
|
||||
mtd-mac-address = <&defaultmac 0>; |
||||
mtd-mac-address-increment = <1>; |
||||
|
||||
fixed-link { |
||||
speed = <1000>; |
||||
full-duplex; |
||||
}; |
||||
}; |
||||
|
||||
gmac2: ethernet@37400000 { |
||||
status = "ok"; |
||||
phy-mode = "sgmii"; |
||||
qcom,id = <2>; |
||||
|
||||
mtd-mac-address = <&defaultmac 0>; |
||||
|
||||
fixed-link { |
||||
speed = <1000>; |
||||
full-duplex; |
||||
}; |
||||
}; |
||||
|
||||
rpm@108000 { |
||||
pinctrl-0 = <&i2c4_pins>; |
||||
pinctrl-names = "default"; |
||||
}; |
||||
}; |
||||
|
||||
gpio-keys { |
||||
compatible = "gpio-keys"; |
||||
pinctrl-0 = <&button_pins>; |
||||
pinctrl-names = "default"; |
||||
|
||||
wifi { |
||||
label = "wifi"; |
||||
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_RFKILL>; |
||||
}; |
||||
|
||||
reset { |
||||
label = "reset"; |
||||
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_RESTART>; |
||||
}; |
||||
|
||||
wps { |
||||
label = "wps"; |
||||
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_WPS_BUTTON>; |
||||
}; |
||||
|
||||
dect { |
||||
label = "dect"; |
||||
gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_PHONE>; |
||||
}; |
||||
|
||||
ledswitch { |
||||
label = "ledswitch"; |
||||
gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; |
||||
linux,code = <KEY_LIGHTS_TOGGLE>; |
||||
}; |
||||
}; |
||||
|
||||
gpio-leds { |
||||
compatible = "gpio-leds"; |
||||
pinctrl-0 = <&led_pins>; |
||||
pinctrl-names = "default"; |
||||
|
||||
dsl { |
||||
label = "vr2600v:white:dsl"; |
||||
gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
usb { |
||||
label = "vr2600v:white:usb"; |
||||
gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
lan { |
||||
label = "vr2600v:white:lan"; |
||||
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
wlan2g { |
||||
label = "vr2600v:white:wlan2g"; |
||||
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
wlan5g { |
||||
label = "vr2600v:white:wlan5g"; |
||||
gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
power: power { |
||||
label = "vr2600v:white:power"; |
||||
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
phone { |
||||
label = "vr2600v:white:phone"; |
||||
gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
wan { |
||||
label = "vr2600v:white:wan"; |
||||
gpios = <&qcom_pinmux 56 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
|
||||
general: general { |
||||
label = "vr2600v:white:general"; |
||||
gpios = <&qcom_pinmux 66 GPIO_ACTIVE_HIGH>; |
||||
}; |
||||
}; |
||||
}; |
||||
|
||||
&adm_dma { |
||||
status = "ok"; |
||||
}; |
||||
Loading…
Reference in new issue