ipq806x/nbg6817: add support for ZyXEL NBG6817

CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO

For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f

For debugging serial console is easily visible on board, no soldering needed.

Signed-off-by: André Valentin <avalentin@marcant.net>
master
André Valentin 8 years ago committed by John Crispin
parent 91b518512d
commit a0ed7af6c6
  1. 5
      target/linux/ipq806x/base-files/etc/board.d/01_leds
  2. 7
      target/linux/ipq806x/base-files/etc/board.d/02_network
  3. 6
      target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
  4. 3
      target/linux/ipq806x/base-files/lib/ipq806x.sh
  5. 18
      target/linux/ipq806x/config-4.4
  6. 341
      target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts
  7. 25
      target/linux/ipq806x/image/Makefile
  8. 3
      target/linux/ipq806x/patches-4.4/800-devicetree.patch

@ -33,6 +33,11 @@ ea8500)
ucidef_set_led_wlan "wifi" "WIFI" "ea8500:green:wifi" "phy0radio"
ucidef_set_led_default "wps" "WPS" "ea8500:green:wps" "0"
;;
nbg6817)
ucidef_set_led_wlan "wlan2g" "WLAN2g" "$board:amber:wifi" "phy1radio"
ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:amber:wifi5" "phy0radio"
ucidef_set_led_netdev "wan" "WAN" "$board:white:internet" "eth1"
;;
*)
;;
esac

@ -35,6 +35,13 @@ ea8500)
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$hw_mac_addr"
;;
nbg6817)
hw_mac_addr=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0"
ucidef_set_interface_macaddr "lan" "$hw_mac_addr"
ucidef_set_interface_macaddr "wan" "$(macaddr_add $hw_mac_addr 1)"
;;
*)
echo "Unsupported hardware. Network interfaces not intialized"
;;

@ -56,6 +56,9 @@ case "$FIRMWARE" in
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ath10kcal_extract "art" 4096 12064
;;
nbg6817)
ath10kcal_extract "0:ART" 4096 12064
;;
r7500v2 |\
r7800)
ath10kcal_extract "art" 4096 12064
@ -72,6 +75,9 @@ case "$FIRMWARE" in
hw_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr)
ath10kcal_extract "art" 20480 12064
;;
nbg6817)
ath10kcal_extract "0:ART" 20480 12064
;;
r7500v2 |\
r7800)
ath10kcal_extract "art" 20480 12064

@ -26,6 +26,9 @@ ipq806x_board_detect() {
*"DB149")
name="db149"
;;
*"NBG6817")
name="nbg6817"
;;
*"R7500")
name="r7500"
;;

@ -61,6 +61,7 @@ CONFIG_ARM_THUMB=y
CONFIG_ARM_UNWIND=y
CONFIG_ARM_VIRT_EXT=y
CONFIG_AT803X_PHY=y
CONFIG_BLK_DEV_LOOP=y
# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
CONFIG_BOUNCE=y
@ -197,11 +198,6 @@ CONFIG_HAVE_GENERIC_DMA_COHERENT=y
CONFIG_HAVE_HW_BREAKPOINT=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
CONFIG_HAVE_KERNEL_GZIP=y
CONFIG_HAVE_KERNEL_LZ4=y
CONFIG_HAVE_KERNEL_LZMA=y
CONFIG_HAVE_KERNEL_LZO=y
CONFIG_HAVE_KERNEL_XZ=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
CONFIG_HAVE_NET_DSA=y
@ -262,6 +258,16 @@ CONFIG_MFD_SYSCON=y
CONFIG_MIGHT_HAVE_CACHE_L2X0=y
CONFIG_MIGHT_HAVE_PCI=y
CONFIG_MIGRATION=y
CONFIG_MMC=y
CONFIG_MMC_ARMMMCI=y
CONFIG_MMC_BLOCK=y
CONFIG_MMC_BLOCK_MINORS=16
CONFIG_MMC_QCOM_DML=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_MSM=y
# CONFIG_MMC_SDHCI_PCI is not set
CONFIG_MMC_SDHCI_PLTFM=y
# CONFIG_MMC_TIFM_SD is not set
CONFIG_MODULES_TREE_LOOKUP=y
CONFIG_MODULES_USE_ELF_REL=y
CONFIG_MSM_GCC_8660=y
@ -378,7 +384,6 @@ CONFIG_QCOM_SCM=y
CONFIG_QCOM_SCM_32=y
# CONFIG_QCOM_SMD is not set
CONFIG_QCOM_SMEM=y
# CONFIG_QCOM_SPMI_TEMP_ALARM is not set
CONFIG_QCOM_WDT=y
CONFIG_RAS=y
CONFIG_RATIONAL=y
@ -389,6 +394,7 @@ CONFIG_RD_GZIP=y
CONFIG_REGMAP=y
CONFIG_REGMAP_MMIO=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_QCOM_RPM=y
# CONFIG_REGULATOR_QCOM_SPMI is not set
CONFIG_RESET_CONTROLLER=y

@ -0,0 +1,341 @@
#include "qcom-ipq8065-v1.0.dtsi"
#include <dt-bindings/input/input.h>
/ {
model = "ZyXEL NBG6817";
compatible = "zyxel,nbg6817", "qcom,ipq8065";
memory@0 {
reg = <0x42000000 0x1e000000>;
device_type = "memory";
};
reserved-memory {
#address-cells = <1>;
#size-cells = <1>;
ranges;
rsvd@41200000 {
reg = <0x41200000 0x300000>;
no-map;
};
};
aliases {
serial0 = &uart4;
mdio-gpio0 = &mdio0;
sdcc1 = &sdcc1;
};
chosen {
bootargs = "root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd";
linux,stdout-path = "serial0:115200n8";
};
soc {
pinmux@800000 {
pinctrl-0 = <&mdio0_pins &rgmii2_pins>;
pinctrl-names = "default";
i2c4_pins: i2c4_pinmux {
mux {
pins = "gpio12", "gpio13";
function = "gsbi4";
drive-strength = <12>;
bias-disable;
};
};
mdio0_pins: mdio0_pins {
mux {
pins = "gpio0", "gpio1";
function = "gpio";
drive-strength = <8>;
bias-disable;
};
clk {
pins = "gpio1";
input-disable;
};
};
rgmii2_pins: rgmii2_pins {
mux {
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
"gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
function = "rgmii2";
drive-strength = <8>;
bias-disable;
};
tx {
pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32" ;
input-disable;
};
};
spi_pins: spi_pins {
mux {
pins = "gpio18", "gpio19", "gpio21";
function = "gsbi5";
drive-strength = <10>;
bias-none;
};
cs {
pins = "gpio20";
drive-strength = <12>;
};
};
};
gsbi@16300000 {
qcom,mode = <GSBI_PROT_I2C_UART>;
status = "ok";
serial@16340000 {
status = "ok";
};
/*
* The i2c device on gsbi4 should not be enabled.
* On ipq806x designs gsbi4 i2c is meant for exclusive
* RPM usage. Turning this on in kernel manifests as
* i2c failure for the RPM.
*/
};
gsbi5: gsbi@1a200000 {
qcom,mode = <GSBI_PROT_SPI>;
status = "ok";
spi4: spi@1a280000 {
status = "ok";
spi-max-frequency = <50000000>;
pinctrl-0 = <&spi_pins>;
pinctrl-names = "default";
cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
flash: m25p80@0 {
compatible = "s25fl512s";
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <51200000>;
reg = <0>;
linux,part-probe = "qcom-smem";
};
};
};
phy@100f8800 { /* USB3 port 1 HS phy */
status = "ok";
};
phy@100f8830 { /* USB3 port 1 SS phy */
status = "ok";
};
phy@110f8800 { /* USB3 port 0 HS phy */
status = "ok";
};
phy@110f8830 { /* USB3 port 0 SS phy */
status = "ok";
};
usb30@0 {
status = "ok";
};
usb30@1 {
status = "ok";
};
pcie0: pci@1b500000 {
status = "ok";
reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_pins>;
pinctrl-names = "default";
};
pcie1: pci@1b700000 {
status = "ok";
reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie1_pins>;
pinctrl-names = "default";
};
mdio0: mdio {
compatible = "virtual,mdio-gpio";
#address-cells = <1>;
#size-cells = <0>;
gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
phy0: ethernet-phy@0 {
device_type = "ethernet-phy";
reg = <0>;
qca,ar8327-initvals = <
0x00004 0x7600000 /* PAD0_MODE */
0x00008 0x1000000 /* PAD5_MODE */
0x0000c 0x80 /* PAD6_MODE */
0x000e4 0xaa545 /* MAC_POWER_SEL */
0x000e0 0xc74164de /* SGMII_CTRL */
0x0007c 0x4e /* PORT0_STATUS */
0x00094 0x4e /* PORT6_STATUS */
0x00970 0x1e864443 /* QM_PORT0_CTRL0 */
0x00974 0x000001c6 /* QM_PORT0_CTRL1 */
0x00978 0x19008643 /* QM_PORT1_CTRL0 */
0x0097c 0x000001c6 /* QM_PORT1_CTRL1 */
0x00980 0x19008643 /* QM_PORT2_CTRL0 */
0x00984 0x000001c6 /* QM_PORT2_CTRL1 */
0x00988 0x19008643 /* QM_PORT3_CTRL0 */
0x0098c 0x000001c6 /* QM_PORT3_CTRL1 */
0x00990 0x19008643 /* QM_PORT4_CTRL0 */
0x00994 0x000001c6 /* QM_PORT4_CTRL1 */
0x00998 0x1e864443 /* QM_PORT5_CTRL0 */
0x0099c 0x000001c6 /* QM_PORT5_CTRL1 */
0x009a0 0x1e864443 /* QM_PORT6_CTRL0 */
0x009a4 0x000001c6 /* QM_PORT6_CTRL1 */
>;
};
phy4: ethernet-phy@4 {
device_type = "ethernet-phy";
reg = <4>;
qca,ar8327-initvals = <
0x000e4 0x6a545 /* MAC_POWER_SEL */
0x0000c 0x80 /* PAD6_MODE */
>;
};
};
gmac1: ethernet@37200000 {
status = "ok";
phy-mode = "rgmii";
qcom,id = <1>;
qcom,phy_mdio_addr = <4>;
qcom,poll_required = <0>;
qcom,rgmii_delay = <1>;
qcom,phy_mii_type = <0>;
qcom,emulation = <0>;
qcom,irq = <255>;
mdiobus = <&mdio0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
gmac2: ethernet@37400000 {
status = "ok";
phy-mode = "sgmii";
qcom,id = <2>;
qcom,phy_mdio_addr = <0>; /* none */
qcom,poll_required = <0>; /* no polling */
qcom,rgmii_delay = <0>;
qcom,phy_mii_type = <1>;
qcom,emulation = <0>;
qcom,irq = <258>;
mdiobus = <&mdio0>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
rpm@108000 {
pinctrl-0 = <&i2c4_pins>;
pinctrl-names = "default";
};
amba {
sdcc1: sdcc@12400000 {
status = "okay";
dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
dma-names = "tx", "rx";
};
};
};
gpio-keys {
compatible = "gpio-keys";
wifi {
label = "wifi";
gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RFKILL>;
};
reset {
label = "reset";
gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
wps {
label = "wps";
gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
gpio-leds {
compatible = "gpio-leds";
internet {
label = "nbg6817:white:internet";
gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
};
power {
label = "nbg6817:white:power";
gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
default-state = "on";
};
wifi {
label = "nbg6817:amber:wifi";
gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
};
wifi5g {
label = "nbg6817:amber:wifi5g";
gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
};
};
gpio_export {
compatible = "gpio-export";
#size-cells = <0>;
usb0_status {
gpio-export,name = "usb0";
gpio-export,output = <1>;
gpios = <&qcom_pinmux 15 GPIO_ACTIVE_HIGH>;
};
usb1_status {
gpio-export,name = "usb1";
gpio-export,output = <1>;
gpios = <&qcom_pinmux 16 GPIO_ACTIVE_HIGH>;
};
usb1_power {
gpio-export,name = "usb1_power";
gpio-export,output = <1>;
gpios = <&qcom_pinmux 14 GPIO_ACTIVE_HIGH>;
};
usb2_power {
gpio-export,name = "usb2_power";
gpio-export,output = <1>;
gpios = <&qcom_pinmux 17 GPIO_ACTIVE_HIGH>;
};
};
};
&adm_dma {
status = "ok";
};

@ -90,6 +90,19 @@ define Device/TpSafeImage
endef
DEVICE_VARS += TPLINK_BOARD_NAME
define Device/ZyXELImage
PROFILES += $$(DEVICE_NAME)
FILESYSTEMS := squashfs
KERNEL_SUFFIX := -uImage
KERNEL = kernel-bin | append-dtb | uImage none | pad-to $$$${KERNEL_SIZE}
KERNEL_NAME := zImage
IMAGES := sysupgrade.tar mmcblk0p5-rootfs.bin mmcblk0p4-kernel.bin
IMAGE/sysupgrade.tar/squashfs := append-rootfs | pad-to $$$${BLOCKSIZE} | sysupgrade-tar rootfs=$$$$@
IMAGE/sysupgrade.tar := sysupgrade-tar
IMAGE/mmcblk0p5-rootfs.bin := append-rootfs | pad-rootfs | pad-to $$$${BLOCKSIZE}
IMAGE/mmcblk0p4-kernel.bin := append-kernel
endef
define Device/AP148
$(call Device/FitImage)
$(call Device/UbiFit)
@ -202,6 +215,16 @@ define Device/R7800
DEVICE_PACKAGES := ath10k-firmware-qca9984
endef
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800
define Device/NBG6817
DEVICE_DTS := qcom-ipq8065-nbg6817
KERNEL_SIZE := 4096k
BLOCKSIZE := 64k
BOARD_NAME := nbg6817
DEVICE_TITLE := ZyXEL NBG6817
DEVICE_PACKAGES := ath10k-firmware-qca9984 e2fsprogs losetup
$(call Device/ZyXELImage)
endef
TARGET_DEVICES += AP148 AP148-legacy C2600 D7800 DB149 EA8500 R7500 R7500v2 R7800 NBG6817
$(eval $(call BuildImage))

@ -12,7 +12,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -506,7 +506,13 @@ dtb-$(CONFIG_ARCH_QCOM) += \
@@ -506,7 +506,14 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8084-ifc6540.dtb \
qcom-apq8084-mtp.dtb \
qcom-ipq8064-ap148.dtb \
@ -22,6 +22,7 @@ Signed-off-by: Jonas Gorski <jogo@openwrt.org>
+ qcom-ipq8064-ea8500.dtb \
+ qcom-ipq8064-r7500.dtb \
+ qcom-ipq8064-r7500v2.dtb \
+ qcom-ipq8065-nbg6817.dtb \
+ qcom-ipq8065-r7800.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \

Loading…
Cancel
Save