This patch ports over support for the device from ar71xx. SOC: AR7370 (Wasp - AR9344 rev2 0001974c) RAM: Winbond W9725G6KB-25 32MiB FLASH: Winbond 25Q64FVSIG 8MiB WLAN: AR9380 Dual-Band 802.11abgn 3x3:3 INPUT: WPS, RESET button (hardware on/off toggle button) LED: Power, LAN, WiFi, 3 RSSI-Leds (low, medium, high) Serial: Header Next to the winbond flash chip (labeld JP1) Pinout is GND - NC - RX - TX - 3V3 (JP1) The Serial setting is 115200-8-N-1. - Installation via uboot's upgrade command 0. attach serial cable 1. interrupt uboot and enter "upgrade code.bin" into the u-boot prompt ar7240> upgrade code.bin 2. rename openwrt...sysupgrade.bin to code.bin on PC 3. run a tftp-client on the PC (shell)$ tftp 192.168.1.230 binary put code.bin 4. wait for the device to finish [...] Copy buff to Flash from 0x9f040000 length 0x79f000 Copy to Flash... write addr: 9f040000 done 5. enter "go" in the u-boot prompt ar7240> go - TFTP ramdisk image boot from the uboot prompt (tftp server defaults to serverip 192.168.1.254) => tftpboot 81000000 initramfs.bin => bootm Tested and working: - LEDs - Buttons - Ethernet - Wi-Fi - OpenWRT sysupgrade For flashing and debricking information see: <https://openwrt.org/toh/wd/rext> Users coming from ar71xx can use sysupgrade too. But I highly advise to no save the old configuration and start from a clean state. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>master
parent
cd9c2492c1
commit
745dee11ac
@ -0,0 +1,174 @@ |
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT |
||||
/dts-v1/; |
||||
|
||||
#include <dt-bindings/gpio/gpio.h> |
||||
#include <dt-bindings/input/input.h> |
||||
|
||||
#include "ar9344.dtsi" |
||||
|
||||
/ { |
||||
model = "Western Digital My Net Wi-Fi Range Extender"; |
||||
compatible = "wd,mynet-wifi-rangeextender", "qca,ar9344"; |
||||
|
||||
chosen { |
||||
bootargs = "console=ttyS0,115200n8"; |
||||
}; |
||||
|
||||
aliases { |
||||
led-boot = &power; |
||||
led-failsafe = &power; |
||||
led-running = &power; |
||||
led-upgrade = &power; |
||||
}; |
||||
|
||||
leds { |
||||
compatible = "gpio-leds"; |
||||
|
||||
power: power { |
||||
label = "mynet-wifi-rangeextender:blue:power"; |
||||
gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; |
||||
/* LED has no off state. It's either on or it blinks */ |
||||
}; |
||||
|
||||
lan { |
||||
label = "mynet-wifi-rangeextender:green:lan"; |
||||
gpios = <&gpio 12 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
|
||||
wifi { |
||||
label = "mynet-wifi-rangeextender:blue:wifi"; |
||||
gpios = <&gpio 19 GPIO_ACTIVE_LOW>; |
||||
linux,default-trigger = "phy0tpt"; |
||||
}; |
||||
|
||||
wifi-rssi-low { |
||||
label = "mynet-wifi-rangeextender:blue:rssi-low"; |
||||
gpios = <&gpio 20 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
|
||||
wifi-rssi-med { |
||||
label = "mynet-wifi-rangeextender:blue:rssi-med"; |
||||
gpios = <&gpio 21 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
|
||||
wifi-rssi-max { |
||||
label = "mynet-wifi-rangeextender:blue:rssi-max"; |
||||
gpios = <&gpio 22 GPIO_ACTIVE_LOW>; |
||||
}; |
||||
}; |
||||
|
||||
keys { |
||||
compatible = "gpio-keys-polled"; |
||||
poll-interval = <50>; |
||||
|
||||
reset { |
||||
linux,code = <KEY_RESTART>; |
||||
gpios = <&gpio 13 GPIO_ACTIVE_LOW>; |
||||
debounce-interval = <60>; |
||||
}; |
||||
|
||||
band-switch { |
||||
linux,code = <BTN_1>; |
||||
gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; |
||||
linux,input-type = <EV_SW>; |
||||
debounce-interval = <60>; |
||||
}; |
||||
|
||||
wps { |
||||
linux,code = <KEY_WPS_BUTTON>; |
||||
gpios = <&gpio 15 GPIO_ACTIVE_LOW>; |
||||
debounce-interval = <60>; |
||||
}; |
||||
}; |
||||
}; |
||||
|
||||
&ref { |
||||
clock-frequency = <25000000>; |
||||
}; |
||||
|
||||
&uart { |
||||
status = "okay"; |
||||
}; |
||||
|
||||
&spi { |
||||
num-cs = <1>; |
||||
|
||||
status = "okay"; |
||||
|
||||
flash@0 { |
||||
compatible = /* "s25fl064k", */ "jedec,spi-nor"; |
||||
reg = <0>; |
||||
spi-max-frequency = <25000000>; |
||||
|
||||
partitions { |
||||
compatible = "fixed-partitions"; |
||||
#address-cells = <1>; |
||||
#size-cells = <1>; |
||||
|
||||
uboot: partition@0 { |
||||
label = "u-boot"; |
||||
reg = <0x0 0x040000>; |
||||
read-only; |
||||
}; |
||||
|
||||
partition@40000 { |
||||
label = "firmware"; |
||||
reg = <0x40000 0x7a0000>; |
||||
compatible = "cybertan,trx"; |
||||
}; |
||||
|
||||
nvram: partition@7e0000 { |
||||
label = "nvram"; |
||||
reg = <0x7e0000 0x10000>; |
||||
}; |
||||
|
||||
art: partition@7f0000 { |
||||
label = "art"; |
||||
reg = <0x7f0000 0x10000>; |
||||
read-only; |
||||
}; |
||||
}; |
||||
}; |
||||
}; |
||||
|
||||
&pcie { |
||||
status = "okay"; |
||||
|
||||
ath9k: wifi@0,0 { |
||||
compatible = "pci168c,0030"; |
||||
reg = <0x0000 0 0 0 0>; |
||||
qca,no-eeprom; |
||||
/* wifi MAC is stored in nvram */ |
||||
}; |
||||
}; |
||||
|
||||
&mdio0 { |
||||
status = "okay"; |
||||
|
||||
phy-mask = <0x10>; |
||||
|
||||
phy4: ethernet-phy@4 { |
||||
reg = <4>; |
||||
}; |
||||
}; |
||||
|
||||
ð0 { |
||||
status = "okay"; |
||||
|
||||
pll-data = <0x0e000000 0x3c000101 0x3c001313>; |
||||
|
||||
/* ethernet MAC is stored in nvram */ |
||||
phy-mode = "rgmii"; |
||||
phy-handle = <&phy4>; |
||||
|
||||
gmac-config { |
||||
device = <&gmac>; |
||||
rgmii-gmac0 = <1>; |
||||
rxd-delay = <3>; |
||||
rxdv-delay = <3>; |
||||
}; |
||||
}; |
||||
|
||||
&mdio1 { |
||||
status = "disabled"; |
||||
}; |
Loading…
Reference in new issue