ppc40x: add support for 3.6

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>

SVN-Revision: 34774
master
Gabor Juhos 12 years ago
parent 2143de1a3d
commit 565cdf58b5
  1. 225
      target/linux/ppc40x/config-3.6
  2. 27
      target/linux/ppc40x/patches-3.6/003-powerpc-add-EBC_BXCR-defines.patch
  3. 446
      target/linux/ppc40x/patches-3.6/004-magicbox.patch
  4. 447
      target/linux/ppc40x/patches-3.6/005-openrb.patch
  5. 433
      target/linux/ppc40x/patches-3.6/101-pata-magicbox-cf-driver.patch
  6. 55
      target/linux/ppc40x/patches-3.6/110-kilauea_openwrt_flashmap.patch
  7. 290
      target/linux/ppc40x/patches-3.6/120-usb-isp116x-hcd-add-of-binding.patch
  8. 111
      target/linux/ppc40x/patches-3.6/121-usb-isp116x-hcd-ppc405-register-access.patch

@ -0,0 +1,225 @@
CONFIG_405EP=y
CONFIG_405EX=y
CONFIG_40x=y
# CONFIG_44x is not set
CONFIG_4xx=y
CONFIG_4xx_SOC=y
# CONFIG_ACADIA is not set
# CONFIG_ADVANCED_OPTIONS is not set
CONFIG_ARCH_ENABLE_MEMORY_HOTPLUG=y
CONFIG_ARCH_ENABLE_MEMORY_HOTREMOVE=y
CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE=y
CONFIG_ARCH_HAS_ILOG2_U32=y
CONFIG_ARCH_HAS_WALK_MEMORY=y
CONFIG_ARCH_HAVE_NMI_SAFE_CMPXCHG=y
CONFIG_ARCH_HIBERNATION_POSSIBLE=y
CONFIG_ARCH_MAY_HAVE_PC_FDC=y
# CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is not set
# CONFIG_ARCH_NO_VIRT_TO_BUS is not set
CONFIG_ARCH_SUPPORTS_DEBUG_PAGEALLOC=y
CONFIG_ARCH_SUPPORTS_MSI=y
CONFIG_ARCH_SUSPEND_POSSIBLE=y
CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
CONFIG_ARCH_WANT_OPTIONAL_GPIOLIB=y
CONFIG_AUDIT_ARCH=y
CONFIG_BOUNCE=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd"
CONFIG_CMDLINE_BOOL=y
CONFIG_CONSISTENT_SIZE=0x00200000
CONFIG_DECOMPRESS_LZMA=y
# CONFIG_DEFAULT_UIMAGE is not set
CONFIG_DTC=y
# CONFIG_E200 is not set
CONFIG_EARLY_PRINTK=y
# CONFIG_EP405 is not set
# CONFIG_EPAPR_BOOT is not set
CONFIG_EXTRA_TARGETS="uImage"
# CONFIG_FSL_ULI1575 is not set
CONFIG_GENERIC_ATOMIC64=y
CONFIG_GENERIC_BUG=y
CONFIG_GENERIC_CLOCKEVENTS=y
CONFIG_GENERIC_CLOCKEVENTS_BUILD=y
CONFIG_GENERIC_CMOS_UPDATE=y
CONFIG_GENERIC_GPIO=y
CONFIG_GENERIC_IO=y
CONFIG_GENERIC_IRQ_SHOW=y
CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
CONFIG_GENERIC_ISA_DMA=y
CONFIG_GENERIC_NVRAM=y
CONFIG_GENERIC_PCI_IOMAP=y
CONFIG_GENERIC_SMP_IDLE_THREAD=y
CONFIG_GENERIC_STRNCPY_FROM_USER=y
CONFIG_GENERIC_STRNLEN_USER=y
# CONFIG_GENERIC_TBSYNC is not set
CONFIG_GENERIC_TIME_VSYSCALL=y
# CONFIG_GEN_RTC is not set
# CONFIG_GE_FPGA is not set
CONFIG_GPIOLIB=y
CONFIG_GPIO_SYSFS=y
CONFIG_HAS_DMA=y
CONFIG_HAS_IOMEM=y
CONFIG_HAS_IOPORT=y
# CONFIG_HAS_RAPIDIO is not set
CONFIG_HAVE_ARCH_JUMP_LABEL=y
CONFIG_HAVE_ARCH_KGDB=y
CONFIG_HAVE_ARCH_TRACEHOOK=y
CONFIG_HAVE_DMA_API_DEBUG=y
CONFIG_HAVE_DMA_ATTRS=y
CONFIG_HAVE_DYNAMIC_FTRACE=y
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
CONFIG_HAVE_FUNCTION_TRACER=y
# CONFIG_HAVE_GENERIC_DMA_COHERENT is not set
CONFIG_HAVE_GENERIC_HARDIRQS=y
CONFIG_HAVE_IDE=y
CONFIG_HAVE_IOREMAP_PROT=y
CONFIG_HAVE_IRQ_WORK=y
CONFIG_HAVE_LATENCYTOP_SUPPORT=y
CONFIG_HAVE_MEMBLOCK=y
CONFIG_HAVE_MEMBLOCK_NODE_MAP=y
CONFIG_HAVE_OPROFILE=y
CONFIG_HAVE_PERF_EVENTS=y
CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
# CONFIG_HAVE_SETUP_PER_CPU_AREA is not set
CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
# CONFIG_HOTFOOT is not set
CONFIG_HW_RANDOM=y
CONFIG_HZ=250
# CONFIG_HZ_100 is not set
CONFIG_HZ_250=y
CONFIG_IBM_EMAC=y
CONFIG_IBM_EMAC_EMAC4=y
CONFIG_IBM_EMAC_POLL_WEIGHT=32
CONFIG_IBM_EMAC_RGMII=y
CONFIG_IBM_EMAC_RXB=256
CONFIG_IBM_EMAC_RX_COPY_THRESHOLD=256
CONFIG_IBM_EMAC_RX_SKB_HEADROOM=0
CONFIG_IBM_EMAC_TXB=256
CONFIG_INITRAMFS_SOURCE=""
CONFIG_IOMMU_HELPER=y
# CONFIG_IPIC is not set
CONFIG_IRQ_DOMAIN=y
CONFIG_IRQ_FORCED_THREADING=y
CONFIG_ISA_DMA_API=y
CONFIG_KERNEL_START=0xc0000000
CONFIG_KILAUEA=y
CONFIG_LEDS_GPIO=m
CONFIG_LOWMEM_SIZE=0x30000000
CONFIG_MAGICBOX=y
# CONFIG_MAKALU is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MAX_ACTIVE_REGIONS=32
# CONFIG_MMIO_NVRAM is not set
# CONFIG_MPIC is not set
# CONFIG_MPIC_U3_HT_IRQS is not set
# CONFIG_MPIC_WEIRD is not set
CONFIG_MTD_CFI_ADV_OPTIONS=y
# CONFIG_MTD_CFI_GEOMETRY is not set
# CONFIG_MTD_CFI_INTELEXT is not set
CONFIG_MTD_OF_PARTS=y
CONFIG_MTD_PHYSMAP_OF=y
CONFIG_NEED_DMA_MAP_STATE=y
# CONFIG_NEED_PER_CPU_EMBED_FIRST_CHUNK is not set
CONFIG_NEED_PER_CPU_KM=y
CONFIG_NEED_SG_DMA_LENGTH=y
CONFIG_NLS=m
# CONFIG_NONSTATIC_KERNEL is not set
CONFIG_NOT_COHERENT_CACHE=y
CONFIG_NR_IRQS=512
CONFIG_OF=y
CONFIG_OF_ADDRESS=y
CONFIG_OF_DEVICE=y
CONFIG_OF_EARLY_FLATTREE=y
CONFIG_OF_FLATTREE=y
CONFIG_OF_GPIO=y
CONFIG_OF_IRQ=y
CONFIG_OF_MTD=y
CONFIG_OF_NET=y
CONFIG_OF_PCI=y
CONFIG_OF_PCI_IRQ=y
CONFIG_OPENRB=y
CONFIG_PAGEFLAGS_EXTENDED=y
CONFIG_PAGE_OFFSET=0xc0000000
CONFIG_PCI=y
CONFIG_PCIEAER=y
CONFIG_PCIEPORTBUS=y
CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
CONFIG_PCI_DOMAINS=y
CONFIG_PCI_MSI=y
CONFIG_PHYSICAL_START=0x00000000
CONFIG_PPC=y
CONFIG_PPC32=y
CONFIG_PPC40x_SIMPLE=y
CONFIG_PPC4xx_MSI=y
CONFIG_PPC4xx_PCI_EXPRESS=y
# CONFIG_PPC64 is not set
# CONFIG_PPC_85xx is not set
# CONFIG_PPC_8xx is not set
# CONFIG_PPC_970_NAP is not set
CONFIG_PPC_ADV_DEBUG_DACS=2
CONFIG_PPC_ADV_DEBUG_DVCS=0
CONFIG_PPC_ADV_DEBUG_IACS=2
CONFIG_PPC_ADV_DEBUG_REGS=y
# CONFIG_PPC_BOOK3S_32 is not set
# CONFIG_PPC_CELL is not set
# CONFIG_PPC_CELL_NATIVE is not set
# CONFIG_PPC_CLOCK is not set
CONFIG_PPC_DCR=y
# CONFIG_PPC_DCR_MMIO is not set
CONFIG_PPC_DCR_NATIVE=y
# CONFIG_PPC_EARLY_DEBUG is not set
# CONFIG_PPC_EPAPR_HV_PIC is not set
# CONFIG_PPC_I8259 is not set
# CONFIG_PPC_ICP_HV is not set
# CONFIG_PPC_ICP_NATIVE is not set
# CONFIG_PPC_ICS_RTAS is not set
CONFIG_PPC_INDIRECT_PCI=y
CONFIG_PPC_MMU_NOHASH=y
# CONFIG_PPC_MM_SLICES is not set
# CONFIG_PPC_MPC106 is not set
CONFIG_PPC_MSI_BITMAP=y
CONFIG_PPC_OF=y
# CONFIG_PPC_P7_NAP is not set
CONFIG_PPC_PCI_CHOICE=y
# CONFIG_PPC_RTAS is not set
CONFIG_PPC_UDBG_16550=y
CONFIG_PPC_WERROR=y
# CONFIG_PPC_WSP is not set
# CONFIG_PPC_XICS is not set
# CONFIG_PQ2ADS is not set
# CONFIG_PREEMPT_RCU is not set
CONFIG_PROC_DEVICETREE=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_SCHED_HRTICK=y
# CONFIG_SCSI_DMA is not set
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_FSL=y
# CONFIG_SERIAL_8250_MANY_PORTS is not set
# CONFIG_SERIAL_8250_RSA is not set
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_OF_PLATFORM=y
# CONFIG_SLAB is not set
CONFIG_SLUB=y
CONFIG_SPARSE_IRQ=y
CONFIG_SWIOTLB=y
CONFIG_TASK_SIZE=0xc0000000
CONFIG_USB=m
CONFIG_USB_ARCH_HAS_XHCI=y
CONFIG_USB_COMMON=m
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_OHCI_BIG_ENDIAN_DESC=y
CONFIG_USB_OHCI_BIG_ENDIAN_MMIO=y
CONFIG_USB_OHCI_HCD=m
CONFIG_USB_OHCI_HCD_PCI=y
# CONFIG_USB_OHCI_HCD_PLATFORM is not set
CONFIG_USB_OHCI_HCD_PPC_OF=y
CONFIG_USB_OHCI_HCD_PPC_OF_BE=y
CONFIG_USB_SUPPORT=y
# CONFIG_USB_UHCI_HCD is not set
# CONFIG_WALNUT is not set
CONFIG_WORD_SIZE=32
# CONFIG_XILINX_SYSACE is not set
# CONFIG_XILINX_VIRTEX_GENERIC_BOARD is not set

@ -0,0 +1,27 @@
--- a/arch/powerpc/boot/dcr.h
+++ b/arch/powerpc/boot/dcr.h
@@ -55,6 +55,14 @@ static const unsigned long sdram_bxcr[]
#define EBC_BXCR(n) (n)
#define EBC_BXCR_BAS 0xfff00000
#define EBC_BXCR_BS 0x000e0000
+#define EBC_BXCR_BS_1M 0x00000000
+#define EBC_BXCR_BS_2M 0x00020000
+#define EBC_BXCR_BS_4M 0x00040000
+#define EBC_BXCR_BS_8M 0x00060000
+#define EBC_BXCR_BS_16M 0x00080000
+#define EBC_BXCR_BS_32M 0x000a0000
+#define EBC_BXCR_BS_64M 0x000c0000
+#define EBC_BXCR_BS_128M 0x000e0000
#define EBC_BXCR_BANK_SIZE(reg) \
(0x100000 << (((reg) & EBC_BXCR_BS) >> 17))
#define EBC_BXCR_BU 0x00018000
@@ -63,6 +71,9 @@ static const unsigned long sdram_bxcr[]
#define EBC_BXCR_BU_WO 0x00010000
#define EBC_BXCR_BU_RW 0x00018000
#define EBC_BXCR_BW 0x00006000
+#define EBC_BXCR_BW_8 0x00000000
+#define EBC_BXCR_BW_16 0x00002000
+#define EBC_BXCR_BW_32 0x00006000
#define EBC_B0AP 0x10
#define EBC_B1AP 0x11
#define EBC_B2AP 0x12

@ -0,0 +1,446 @@
--- /dev/null
+++ b/arch/powerpc/boot/cuboot-magicbox.c
@@ -0,0 +1,98 @@
+/*
+ * Old U-boot compatibility for Magicbox boards
+ *
+ * Author: Imre Kaloz <kaloz@openwrt.org>
+ * Gabor Juhos <juhosg@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "io.h"
+#include "dcr.h"
+#include "stdio.h"
+#include "4xx.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_4xx
+#define TARGET_405EP
+#include "ppcboot.h"
+
+static bd_t bd;
+
+static void fixup_perwe(void)
+{
+
+#define DCRN_CPC0_PCI_BASE 0xf9
+
+ /* Turn on PerWE instead of PCIINT */
+ mtdcr(DCRN_CPC0_PCI_BASE,
+ mfdcr(DCRN_CPC0_PCI_BASE) | (0x80000000L >> 27));
+
+#undef DCRN_CPC0_PCI_BASE
+}
+
+static void fixup_cf_card(void)
+{
+
+#define CF_CS0_BASE 0xff100000
+#define CF_CS1_BASE 0xff200000
+
+ /* PerCS1 (CF's CS0): base 0xff100000, 16-bit, rw */
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B1CR);
+ mtdcr(DCRN_EBC0_CFGDATA, CF_CS0_BASE | EBC_BXCR_BS_1M |
+ EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B1AP);
+ mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
+
+ /* PerCS2 (CF's CS1): base 0xff200000, 16-bit, rw */
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B2CR);
+ mtdcr(DCRN_EBC0_CFGDATA, CF_CS1_BASE | EBC_BXCR_BS_1M |
+ EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B2AP);
+ mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
+
+#undef CF_CS0_BASE
+#undef CF_CS1_BASE
+}
+
+static void magicbox_fixups(void)
+{
+ ibm405ep_fixup_clocks(bd.bi_procfreq / 8);
+ ibm4xx_sdram_fixup_memsize();
+
+ /* Magicbox v1 has only one ethernet, one serial and no
+ * CF slot -- detect it using it's fake enet1addr
+ */
+ if ((bd.bi_enet1addr[2] == 0x02) &&
+ (bd.bi_enet1addr[3] == 0xfa) &&
+ (bd.bi_enet1addr[4] == 0xf0) &&
+ (bd.bi_enet1addr[5] == 0x80)) {
+ void *devp;
+ devp = finddevice("/plb/opb/ethernet@ef600900");
+ del_node(devp);
+ devp = finddevice("/plb/opb/serial@ef600400");
+ del_node(devp);
+ devp = finddevice("/plb/ebc/cf_card@ff100000");
+ del_node(devp);
+
+ } else {
+ fixup_perwe();
+ fixup_cf_card();
+ }
+
+ dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ CUBOOT_INIT();
+ platform_ops.fixups = magicbox_fixups;
+ platform_ops.exit = ibm40x_dbcr_reset;
+ fdt_init(_dtb_start);
+ serial_console_init();
+}
--- /dev/null
+++ b/arch/powerpc/boot/dts/magicbox.dts
@@ -0,0 +1,285 @@
+/*
+ * Device Tree Source for Magicbox boards
+ *
+ * Copyright 2008-2009 Imre Kaloz <kaloz@openwrt.org>
+ * Copyright 2009 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * Based on walnut.dts
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "magicbox";
+ compatible = "magicbox";
+ dcr-parent = <&{/cpus/cpu@0}>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ ethernet1 = &EMAC1;
+ serial0 = &UART0;
+ serial1 = &UART1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,405EP";
+ reg = <0x00000000>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ timebase-frequency = <0>; /* Filled in by zImage */
+ i-cache-line-size = <0x20>;
+ d-cache-line-size = <0x20>;
+ i-cache-size = <0x4000>;
+ d-cache-size = <0x4000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000>; /* Filled in by zImage */
+ };
+
+ UIC0: interrupt-controller {
+ compatible = "ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0x0c0 0x009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ plb {
+ compatible = "ibm,plb3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ SDRAM0: memory-controller {
+ compatible = "ibm,sdram-405ep";
+ dcr-reg = <0x010 0x002>;
+ };
+
+ MAL: mcmal {
+ compatible = "ibm,mcmal-405ep", "ibm,mcmal";
+ dcr-reg = <0x180 0x062>;
+ num-tx-chans = <4>;
+ num-rx-chans = <2>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0xb 0x4 /* TXEOB */
+ 0xc 0x4 /* RXEOB */
+ 0xa 0x4 /* SERR */
+ 0xd 0x4 /* TXDE */
+ 0xe 0x4 /* RXDE */>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-405ep", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0xef600000 0xef600000 0x00a00000>;
+ dcr-reg = <0x0a0 0x005>;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ UART0: serial@ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0xef600300 0x00000008>;
+ virtual-reg = <0xef600300>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <115200>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x0 0x4>;
+ };
+
+ UART1: serial@ef600400 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0xef600400 0x00000008>;
+ virtual-reg = <0xef600400>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <115200>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x1 0x4>;
+ };
+
+ IIC: i2c@ef600500 {
+ compatible = "ibm,iic-405ep", "ibm,iic";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xef600500 0x00000011>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x2 0x4>;
+
+ dtt@48 {
+ compatible = "national,lm75";
+ reg = <0x48>;
+ };
+
+ eeprom@50 {
+ compatible = "at24,24c16";
+ reg = <0x50>;
+ };
+ };
+
+ GPIO0: gpio-controller@ef600700 {
+ compatible = "ibm,ppc4xx-gpio";
+ reg = <0xef600700 0x00000020>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ EMAC0: ethernet@ef600800 {
+ linux,network-index = <0x0>;
+ device_type = "network";
+ compatible = "ibm,emac-405ep", "ibm,emac";
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0xf 0x4 /* Ethernet */
+ 0x9 0x4 /* Ethernet Wake Up */>;
+ local-mac-address = [000000000000]; /* Filled in by zImage */
+ reg = <0xef600800 0x00000070>;
+ mal-device = <&MAL>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <0x5dc>;
+ rx-fifo-size = <0x1000>;
+ tx-fifo-size = <0x800>;
+ phy-mode = "mii";
+ phy-map = <0x00000000>;
+ };
+
+ EMAC1: ethernet@ef600900 {
+ linux,network-index = <0x1>;
+ device_type = "network";
+ compatible = "ibm,emac-405ep", "ibm,emac";
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0x11 0x4 /* Ethernet */
+ 0x09 0x4 /* Ethernet Wake Up */>;
+ local-mac-address = [000000000000]; /* Filled in by zImage */
+ reg = <0xef600900 0x00000070>;
+ mal-device = <&MAL>;
+ mal-tx-channel = <2>;
+ mal-rx-channel = <1>;
+ cell-index = <1>;
+ max-frame-size = <0x5dc>;
+ rx-fifo-size = <0x1000>;
+ tx-fifo-size = <0x800>;
+ mdio-device = <&EMAC0>;
+ phy-mode = "mii";
+ phy-map = <0x00000001>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ user {
+ label = "magicbox:red:user";
+ gpios = <&GPIO0 2 1>;
+ };
+ };
+ };
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-405ep", "ibm,ebc";
+ dcr-reg = <0x012 0x002>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* The ranges property is supplied by the bootwrapper
+ * and is based on the firmware's configuration of the
+ * EBC bridge
+ */
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ cf_card@ff100000 {
+ compatible = "magicbox-cf", "pata-magicbox-cf";
+ reg = <0x00000000 0xff100000 0x00001000
+ 0x00000000 0xff200000 0x00001000>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x19 0x1 /* IRQ_TYPE_EDGE_RISING */ >;
+ };
+
+ nor_flash@ffc00000 {
+ compatible = "cfi-flash";
+ bank-width = <2>;
+ reg = <0x00000000 0xffc00000 0x00400000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition0@0 {
+ label = "linux";
+ reg = <0x0 0x140000>;
+ };
+ partition1@120000 {
+ label = "rootfs";
+ reg = <0x140000 0x280000>;
+ };
+ partition2@3c0000 {
+ label = "u-boot";
+ reg = <0x3c0000 0x30000>;
+ read-only;
+ };
+ partition3@0 {
+ label = "firmware";
+ reg = <0x0 0x3c0000>;
+ };
+ };
+ };
+
+ PCI0: pci@ec000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb405ep-pci", "ibm,plb-pci";
+ primary;
+ reg = <0xeec00000 0x00000008 /* Config space access */
+ 0xeed80000 0x00000004 /* IACK */
+ 0xeed80000 0x00000004 /* Special cycle */
+ 0xef480000 0x00000040>; /* Internal registers */
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed. Chip supports a second
+ * IO range but we don't use it for now
+ */
+ ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x20000000
+ 0x01000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
+
+ interrupt-map-mask = <0xf800 0x0 0x0 0x0>;
+ interrupt-map = <
+ /* IDSEL 1 */
+ 0x800 0x0 0x0 0x0 &UIC0 0x1c 0x8
+
+ /* IDSEL 2 */
+ 0x1000 0x0 0x0 0x0 &UIC0 0x1d 0x8
+
+ /* IDSEL 3 */
+ 0x1800 0x0 0x0 0x0 &UIC0 0x1e 0x8
+
+ /* IDSEL 4 */
+ 0x2000 0x0 0x0 0x0 &UIC0 0x1f 0x8
+ >;
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/plb/opb/serial@ef600300";
+ };
+};
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -43,6 +43,7 @@ $(obj)/cuboot-hotfoot.o: BOOTCFLAGS += -
$(obj)/cuboot-taishan.o: BOOTCFLAGS += -mcpu=440
$(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=440
$(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
+$(obj)/cuboot-magicbox.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-iss4xx.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-currituck.o: BOOTCFLAGS += -mcpu=405
@@ -78,7 +79,8 @@ src-plat-y := of.c
src-plat-$(CONFIG_40x) += fixed-head.S ep405.c cuboot-hotfoot.c \
treeboot-walnut.c cuboot-acadia.c \
cuboot-kilauea.c simpleboot.c \
- virtex405-head.S virtex.c
+ virtex405-head.S virtex.c \
+ cuboot-magicbox.c
src-plat-$(CONFIG_44x) += treeboot-ebony.c cuboot-ebony.c treeboot-bamboo.c \
cuboot-bamboo.c cuboot-sam440ep.c \
cuboot-sequoia.c cuboot-rainier.c \
@@ -220,6 +222,7 @@ image-$(CONFIG_HOTFOOT) += cuImage.hot
image-$(CONFIG_WALNUT) += treeImage.walnut
image-$(CONFIG_ACADIA) += cuImage.acadia
image-$(CONFIG_OBS600) += uImage.obs600
+image-$(CONFIG_MAGICBOX) += cuImage.magicbox
# Board ports in arch/powerpc/platform/44x/Kconfig
image-$(CONFIG_EBONY) += treeImage.ebony cuImage.ebony
--- a/arch/powerpc/platforms/40x/Kconfig
+++ b/arch/powerpc/platforms/40x/Kconfig
@@ -38,6 +38,16 @@ config KILAUEA
help
This option enables support for the AMCC PPC405EX evaluation board.
+config MAGICBOX
+ bool "Magicbox"
+ depends on 40x
+ default n
+ select PPC40x_SIMPLE
+ select 405EP
+ select PCI
+ help
+ This option enables support for the Magicbox boards.
+
config MAKALU
bool "Makalu"
depends on 40x
--- a/arch/powerpc/platforms/40x/ppc40x_simple.c
+++ b/arch/powerpc/platforms/40x/ppc40x_simple.c
@@ -57,6 +57,7 @@ static const char *board[] __initdata =
"amcc,makalu",
"apm,klondike",
"est,hotfoot",
+ "magicbox",
"plathome,obs600"
};

@ -0,0 +1,447 @@
--- /dev/null
+++ b/arch/powerpc/boot/cuboot-openrb.c
@@ -0,0 +1,94 @@
+/*
+ * Old U-boot compatibility for OpenRB boards
+ *
+ * Author: Gabor Juhos <juhosg@openwrt.org>
+ * Imre Kaloz <kaloz@openwrt.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include "ops.h"
+#include "io.h"
+#include "dcr.h"
+#include "stdio.h"
+#include "4xx.h"
+#include "44x.h"
+#include "cuboot.h"
+
+#define TARGET_4xx
+#define TARGET_405EP
+#include "ppcboot.h"
+
+static bd_t bd;
+
+static void fixup_perwe(void)
+{
+#define DCRN_CPC0_PCI_BASE 0xf9
+
+ /* Turn on PerWE instead of PCIINT */
+ mtdcr(DCRN_CPC0_PCI_BASE,
+ mfdcr(DCRN_CPC0_PCI_BASE) | (0x80000000L >> 27));
+
+#undef DCRN_CPC0_PCI_BASE
+}
+
+static void fixup_cf_card(void)
+{
+#define CF_CS0_BASE 0xff100000
+#define CF_CS1_BASE 0xff200000
+
+ /* PerCS1 (CF's CS0): base 0xff100000, 16-bit, rw */
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B1CR);
+ mtdcr(DCRN_EBC0_CFGDATA, CF_CS0_BASE | EBC_BXCR_BS_1M |
+ EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B1AP);
+ mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
+
+ /* PerCS2 (CF's CS1): base 0xff200000, 16-bit, rw */
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B2CR);
+ mtdcr(DCRN_EBC0_CFGDATA, CF_CS1_BASE | EBC_BXCR_BS_1M |
+ EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B2AP);
+ mtdcr(DCRN_EBC0_CFGDATA, 0x080bd800);
+
+#undef CF_CS0_BASE
+#undef CF_CS1_BASE
+}
+
+static void fixup_isp116x(void)
+{
+#define ISP116X_CS_BASE 0xf0000000
+
+ /* PerCS3 (ISP1160's CS): base 0xf0000000, size 32MB, 16-bit, rw */
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B3CR);
+ mtdcr(DCRN_EBC0_CFGDATA, ISP116X_CS_BASE | EBC_BXCR_BS_32M |
+ EBC_BXCR_BU_RW | EBC_BXCR_BW_16);
+ mtdcr(DCRN_EBC0_CFGADDR, EBC_B3AP);
+ mtdcr(DCRN_EBC0_CFGDATA, 0x03016600);
+
+#undef ISP116X_CS_BASE
+}
+
+static void openrb_fixups(void)
+{
+ ibm405ep_fixup_clocks(bd.bi_procfreq / 8);
+ ibm4xx_sdram_fixup_memsize();
+
+ fixup_perwe();
+ fixup_cf_card();
+ fixup_isp116x();
+
+ dt_fixup_mac_addresses(&bd.bi_enetaddr, &bd.bi_enet1addr);
+}
+
+void platform_init(unsigned long r3, unsigned long r4, unsigned long r5,
+ unsigned long r6, unsigned long r7)
+{
+ CUBOOT_INIT();
+ platform_ops.fixups = openrb_fixups;
+ platform_ops.exit = ibm40x_dbcr_reset;
+ fdt_init(_dtb_start);
+ serial_console_init();
+}
--- /dev/null
+++ b/arch/powerpc/boot/dts/openrb.dts
@@ -0,0 +1,291 @@
+/*
+ * Device Tree Source for OpenRB boards
+ *
+ * Copyright 2009 Gabor Juhos <juhosg@openwrt.org>
+ * Copyright 2009 Imre Kaloz <kaloz@openwrt.org>
+ *
+ * Based on walnut.dts
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ model = "openrb";
+ compatible = "openrb";
+ dcr-parent = <&{/cpus/cpu@0}>;
+
+ aliases {
+ ethernet0 = &EMAC0;
+ ethernet1 = &EMAC1;
+ serial0 = &UART0;
+ serial1 = &UART1;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ model = "PowerPC,405EP";
+ reg = <0x00000000>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ timebase-frequency = <0>; /* Filled in by zImage */
+ i-cache-line-size = <0x20>;
+ d-cache-line-size = <0x20>;
+ i-cache-size = <0x4000>;
+ d-cache-size = <0x4000>;
+ dcr-controller;
+ dcr-access-method = "native";
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x00000000>; /* Filled in by zImage */
+ };
+
+ UIC0: interrupt-controller {
+ compatible = "ibm,uic";
+ interrupt-controller;
+ cell-index = <0>;
+ dcr-reg = <0x0c0 0x009>;
+ #address-cells = <0>;
+ #size-cells = <0>;
+ #interrupt-cells = <2>;
+ };
+
+ plb {
+ compatible = "ibm,plb3";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ SDRAM0: memory-controller {
+ compatible = "ibm,sdram-405ep";
+ dcr-reg = <0x010 0x002>;
+ };
+
+ MAL: mcmal {
+ compatible = "ibm,mcmal-405ep", "ibm,mcmal";
+ dcr-reg = <0x180 0x062>;
+ num-tx-chans = <4>;
+ num-rx-chans = <2>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0xb 0x4 /* TXEOB */
+ 0xc 0x4 /* RXEOB */
+ 0xa 0x4 /* SERR */
+ 0xd 0x4 /* TXDE */
+ 0xe 0x4 /* RXDE */>;
+ };
+
+ POB0: opb {
+ compatible = "ibm,opb-405ep", "ibm,opb";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0xef600000 0xef600000 0x00a00000>;
+ dcr-reg = <0x0a0 0x005>;
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ UART0: serial@ef600300 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0xef600300 0x00000008>;
+ virtual-reg = <0xef600300>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <115200>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x0 0x4>;
+ };
+
+ UART1: serial@ef600400 {
+ device_type = "serial";
+ compatible = "ns16550";
+ reg = <0xef600400 0x00000008>;
+ virtual-reg = <0xef600400>;
+ clock-frequency = <0>; /* Filled in by zImage */
+ current-speed = <115200>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x1 0x4>;
+ };
+
+ IIC: i2c@ef600500 {
+ compatible = "ibm,iic-405ep", "ibm,iic";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xef600500 0x00000011>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x2 0x4>;
+
+ eeprom@50 {
+ compatible = "at24,24c16";
+ reg = <0x50>;
+ };
+ };
+
+ GPIO0: gpio-controller@ef600700 {
+ compatible = "ibm,ppc4xx-gpio";
+ reg = <0xef600700 0x00000020>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ EMAC0: ethernet@ef600800 {
+ linux,network-index = <0x0>;
+ device_type = "network";
+ compatible = "ibm,emac-405ep", "ibm,emac";
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0xf 0x4 /* Ethernet */
+ 0x9 0x4 /* Ethernet Wake Up */>;
+ local-mac-address = [000000000000]; /* Filled in by zImage */
+ reg = <0xef600800 0x00000070>;
+ mal-device = <&MAL>;
+ mal-tx-channel = <0>;
+ mal-rx-channel = <0>;
+ cell-index = <0>;
+ max-frame-size = <0x5dc>;
+ rx-fifo-size = <0x1000>;
+ tx-fifo-size = <0x800>;
+ phy-mode = "mii";
+ phy-map = <0x00000000>;
+ };
+
+ EMAC1: ethernet@ef600900 {
+ linux,network-index = <0x1>;
+ device_type = "network";
+ compatible = "ibm,emac-405ep", "ibm,emac";
+ interrupt-parent = <&UIC0>;
+ interrupts = <
+ 0x11 0x4 /* Ethernet */
+ 0x09 0x4 /* Ethernet Wake Up */>;
+ local-mac-address = [000000000000]; /* Filled in by zImage */
+ reg = <0xef600900 0x00000070>;
+ mal-device = <&MAL>;
+ mal-tx-channel = <2>;
+ mal-rx-channel = <1>;
+ cell-index = <1>;
+ max-frame-size = <0x5dc>;
+ rx-fifo-size = <0x1000>;
+ tx-fifo-size = <0x800>;
+ mdio-device = <&EMAC0>;
+ phy-mode = "mii";
+ phy-map = <0x00000001>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ user {
+ label = "openrb:green:user";
+ gpios = <&GPIO0 2 1>;
+ };
+ };
+ };
+
+ EBC0: ebc {
+ compatible = "ibm,ebc-405ep", "ibm,ebc";
+ dcr-reg = <0x012 0x002>;
+ #address-cells = <2>;
+ #size-cells = <1>;
+ /* The ranges property is supplied by the bootwrapper
+ * and is based on the firmware's configuration of the
+ * EBC bridge
+ */
+ clock-frequency = <0>; /* Filled in by zImage */
+
+ isp116x@f0000000 {
+ compatible = "isp116x-hcd";
+ oc_enable;
+ int_act_high;
+ int_edge_triggered;
+ reg = <0x00000000 0xf0000000 0x00000002 /* data */
+ 0x00000000 0xf1000000 0x00000002 /* addr */ >;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x1b 0x1 /* IRQ_TYPE_EDGE_RISING */ >;
+ };
+
+ cf_card@ff100000 {
+ compatible = "magicbox-cf", "pata-magicbox-cf";
+ reg = <0x00000000 0xff100000 0x00001000
+ 0x00000000 0xff200000 0x00001000>;
+ interrupt-parent = <&UIC0>;
+ interrupts = <0x19 0x1 /* IRQ_TYPE_EDGE_RISING */ >;
+ };
+
+ nor_flash@ff800000 {
+ compatible = "cfi-flash";
+ bank-width = <2>;
+ reg = <0x00000000 0xff800000 0x00800000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ partition0@0 {
+ label = "linux";
+ reg = <0x0 0x140000>;
+ };
+ partition1@120000 {
+ label = "rootfs";
+ reg = <0x140000 0x680000>;
+ };
+ partition2@7c0000 {
+ label = "u-boot";
+ reg = <0x7c0000 0x30000>;
+ read-only;
+ };
+ partition3@0 {
+ label = "firmware";
+ reg = <0x0 0x7c0000>;
+ };
+ };
+ };
+
+ PCI0: pci@ec000000 {
+ device_type = "pci";
+ #interrupt-cells = <1>;
+ #size-cells = <2>;
+ #address-cells = <3>;
+ compatible = "ibm,plb405ep-pci", "ibm,plb-pci";
+ primary;
+ reg = <0xeec00000 0x00000008 /* Config space access */
+ 0xeed80000 0x00000004 /* IACK */
+ 0xeed80000 0x00000004 /* Special cycle */
+ 0xef480000 0x00000040>; /* Internal registers */
+
+ /* Outbound ranges, one memory and one IO,
+ * later cannot be changed. Chip supports a second
+ * IO range but we don't use it for now
+ */
+ ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x20000000
+ 0x01000000 0x00000000 0x00000000 0xe8000000 0x00000000 0x00010000>;
+
+ /* Inbound 2GB range starting at 0 */
+ dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x80000000>;
+
+ interrupt-map-mask = <0xf800 0x0 0x0 0x0>;
+ interrupt-map = <
+ /* IDSEL 1 */
+ 0x800 0x0 0x0 0x0 &UIC0 0x1c 0x8
+
+ /* IDSEL 2 */
+ 0x1000 0x0 0x0 0x0 &UIC0 0x1d 0x8
+
+ /* IDSEL 3 */
+ 0x1800 0x0 0x0 0x0 &UIC0 0x1e 0x8
+
+ /* IDSEL 4 */
+ 0x2000 0x0 0x0 0x0 &UIC0 0x1f 0x8
+ >;
+ };
+ };
+
+ chosen {
+ linux,stdout-path = "/plb/opb/serial@ef600300";
+ };
+};
--- a/arch/powerpc/boot/Makefile
+++ b/arch/powerpc/boot/Makefile
@@ -44,6 +44,7 @@ $(obj)/cuboot-taishan.o: BOOTCFLAGS += -
$(obj)/cuboot-katmai.o: BOOTCFLAGS += -mcpu=440
$(obj)/cuboot-acadia.o: BOOTCFLAGS += -mcpu=405
$(obj)/cuboot-magicbox.o: BOOTCFLAGS += -mcpu=405
+$(obj)/cuboot-openrb.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-walnut.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-iss4xx.o: BOOTCFLAGS += -mcpu=405
$(obj)/treeboot-currituck.o: BOOTCFLAGS += -mcpu=405
@@ -80,7 +81,7 @@ src-plat-$(CONFIG_40x) += fixed-head.S e
treeboot-walnut.c cuboot-acadia.c \
cuboot-kilauea.c simpleboot.c \
virtex405-head.S virtex.c \
- cuboot-magicbox.c
+ cuboot-magicbox.c cuboot-openrb
src-plat-$(CONFIG_44x) += treeboot-ebony.c cuboot-ebony.c treeboot-bamboo.c \
cuboot-bamboo.c cuboot-sam440ep.c \
cuboot-sequoia.c cuboot-rainier.c \
@@ -223,6 +224,7 @@ image-$(CONFIG_WALNUT) += treeImage.wa
image-$(CONFIG_ACADIA) += cuImage.acadia
image-$(CONFIG_OBS600) += uImage.obs600
image-$(CONFIG_MAGICBOX) += cuImage.magicbox
+image-$(CONFIG_OPENRB) += cuImage.openrb
# Board ports in arch/powerpc/platform/44x/Kconfig
image-$(CONFIG_EBONY) += treeImage.ebony cuImage.ebony
--- a/arch/powerpc/platforms/40x/Kconfig
+++ b/arch/powerpc/platforms/40x/Kconfig
@@ -48,6 +48,16 @@ config MAGICBOX
help
This option enables support for the Magicbox boards.
+config OPENRB
+ bool "OpenRB"
+ depends on 40x
+ default n
+ select PPC40x_SIMPLE
+ select 405EP
+ select PCI
+ help
+ This option enables support for the OpenRB boards.
+
config MAKALU
bool "Makalu"
depends on 40x
--- a/arch/powerpc/platforms/40x/ppc40x_simple.c
+++ b/arch/powerpc/platforms/40x/ppc40x_simple.c
@@ -58,6 +58,7 @@ static const char *board[] __initdata =
"apm,klondike",
"est,hotfoot",
"magicbox",
+ "openrb",
"plathome,obs600"
};

@ -0,0 +1,433 @@
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -144,6 +144,16 @@ config PDC_ADMA
If unsure, say N.
+config PATA_MAGICBOX_CF
+ tristate "Magicbox/OpenRB Compact Flash support"
+ depends on MAGICBOX || OPENRB
+ help
+ This option enables support for a Compact Flash conected on
+ the ppc405ep expansion bus. This driver had been written for
+ the Magicbox v2 and OpenRB boards.
+
+ If unsure, say N.
+
config PATA_OCTEON_CF
tristate "OCTEON Boot Bus Compact Flash support"
depends on CPU_CAVIUM_OCTEON
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_PATA_AT91) += pata_at91.o
obj-$(CONFIG_PATA_CMD640_PCI) += pata_cmd640.o
obj-$(CONFIG_PATA_ISAPNP) += pata_isapnp.o
obj-$(CONFIG_PATA_IXP4XX_CF) += pata_ixp4xx_cf.o
+obj-$(CONFIG_PATA_MAGICBOX_CF) += pata_magicbox_cf.o
obj-$(CONFIG_PATA_MPIIX) += pata_mpiix.o
obj-$(CONFIG_PATA_NS87410) += pata_ns87410.o
obj-$(CONFIG_PATA_OPTI) += pata_opti.o
--- /dev/null
+++ b/drivers/ata/pata_magicbox_cf.c
@@ -0,0 +1,401 @@
+/*
+ * PATA/CompactFlash driver for the MagicBox v2/OpenRB boards.
+ *
+ * Copyright (C) 2009,2012 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * Based on the IDE driver by Wojtek Kaniewski <wojtekka@toxygen.net>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/ioport.h>
+#include <linux/libata.h>
+#include <linux/irq.h>
+//#include <linux/of.h>
+//#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <scsi/scsi_host.h>
+
+#define DRV_DESC "PATA/CompactFlash driver for Magicbox/OpenRB boards"
+#define DRV_NAME "pata_magicbox_cf"
+#define DRV_VERSION "0.1.0"
+
+#define MAGICBOX_CF_REG_CMD (2 * ATA_REG_CMD)
+#define MAGICBOX_CF_REG_DATA (2 * ATA_REG_DATA)
+#define MAGICBOX_CF_REG_ERR (2 * ATA_REG_ERR)
+#define MAGICBOX_CF_REG_FEATURE (2 * ATA_REG_FEATURE)
+#define MAGICBOX_CF_REG_NSECT (2 * ATA_REG_NSECT)
+#define MAGICBOX_CF_REG_LBAL (2 * ATA_REG_LBAL)
+#define MAGICBOX_CF_REG_LBAM (2 * ATA_REG_LBAM)
+#define MAGICBOX_CF_REG_LBAH (2 * ATA_REG_LBAH)
+#define MAGICBOX_CF_REG_DEVICE (2 * ATA_REG_DEVICE)
+#define MAGICBOX_CF_REG_STATUS (2 * ATA_REG_STATUS)
+#define MAGICBOX_CF_REG_ALTSTATUS (2 * 6)
+#define MAGICBOX_CF_REG_CTL (2 * 6)
+
+#define MAGICBOX_CF_MAXPORTS 1
+
+struct magicbox_cf_info {
+ void __iomem *base;
+ void __iomem *ctrl;
+};
+
+static inline u8 magicbox_cf_inb(void __iomem *port)
+{
+ return (u8) (readw(port) >> 8) & 0xff;
+}
+
+static inline void magicbox_cf_outb(void __iomem *port, u8 value)
+{
+ writew(value << 8, port);
+}
+
+static int magicbox_cf_set_mode(struct ata_link *link,
+ struct ata_device **error)
+{
+ struct ata_device *dev;
+
+ ata_for_each_dev(dev, link, ENABLED) {
+ ata_dev_printk(dev, KERN_INFO, "configured for PIO0\n");
+ dev->pio_mode = XFER_PIO_0;
+ dev->xfer_mode = XFER_PIO_0;
+ dev->xfer_shift = ATA_SHIFT_PIO;
+ dev->flags |= ATA_DFLAG_PIO;
+ }
+
+ return 0;
+}
+
+static void magicbox_cf_exec_command(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
+
+ magicbox_cf_outb(ap->ioaddr.command_addr, tf->command);
+ ata_sff_pause(ap);
+}
+
+static u8 magicbox_cf_check_status(struct ata_port *ap)
+{
+ u8 status;
+
+ status = magicbox_cf_inb(ap->ioaddr.status_addr);
+
+ DPRINTK("ata%u: status 0x%X, from %p\n", ap->print_id, status,
+ ap->ioaddr.status_addr);
+
+ return status;
+}
+
+static u8 magicbox_cf_check_altstatus(struct ata_port *ap)
+{
+ u8 altstatus;
+
+ altstatus = magicbox_cf_inb(ap->ioaddr.altstatus_addr);
+
+ DPRINTK("ata%u: altstatus 0x%X, from %p\n", ap->print_id,
+ altstatus, ap->ioaddr.altstatus_addr);
+
+ return altstatus;
+}
+
+static void magicbox_cf_dev_select(struct ata_port *ap, unsigned int device)
+{
+ /* Nothing to do. We are supporting one device only. */
+}
+
+static void magicbox_cf_tf_load(struct ata_port *ap,
+ const struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+ unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
+
+ if (tf->ctl != ap->last_ctl) {
+ magicbox_cf_outb(ioaddr->ctl_addr, tf->ctl);
+ ap->last_ctl = tf->ctl;
+ ata_wait_idle(ap);
+ }
+
+ if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
+ magicbox_cf_outb(ioaddr->feature_addr, tf->hob_feature);
+ magicbox_cf_outb(ioaddr->nsect_addr, tf->hob_nsect);
+ magicbox_cf_outb(ioaddr->lbal_addr, tf->hob_lbal);
+ magicbox_cf_outb(ioaddr->lbam_addr, tf->hob_lbam);
+ magicbox_cf_outb(ioaddr->lbah_addr, tf->hob_lbah);
+ VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n",
+ tf->hob_feature,
+ tf->hob_nsect,
+ tf->hob_lbal,
+ tf->hob_lbam,
+ tf->hob_lbah);
+ }
+
+ if (is_addr) {
+ magicbox_cf_outb(ioaddr->feature_addr, tf->feature);
+ magicbox_cf_outb(ioaddr->nsect_addr, tf->nsect);
+ magicbox_cf_outb(ioaddr->lbal_addr, tf->lbal);
+ magicbox_cf_outb(ioaddr->lbam_addr, tf->lbam);
+ magicbox_cf_outb(ioaddr->lbah_addr, tf->lbah);
+ VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+ }
+
+ if (tf->flags & ATA_TFLAG_DEVICE) {
+ magicbox_cf_outb(ioaddr->device_addr, tf->device);
+ VPRINTK("device 0x%X\n", tf->device);
+ }
+
+ ata_wait_idle(ap);
+}
+
+static void magicbox_cf_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
+{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
+
+ tf->command = magicbox_cf_inb(ap->ioaddr.status_addr);
+ tf->feature = magicbox_cf_inb(ioaddr->error_addr);
+ tf->nsect = magicbox_cf_inb(ioaddr->nsect_addr);
+ tf->lbal = magicbox_cf_inb(ioaddr->lbal_addr);
+ tf->lbam = magicbox_cf_inb(ioaddr->lbam_addr);
+ tf->lbah = magicbox_cf_inb(ioaddr->lbah_addr);
+ tf->device = magicbox_cf_inb(ioaddr->device_addr);
+ VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+
+ if (tf->flags & ATA_TFLAG_LBA48) {
+ magicbox_cf_outb(ioaddr->ctl_addr, tf->ctl | ATA_HOB);
+ tf->hob_feature = magicbox_cf_inb(ioaddr->error_addr);
+ tf->hob_nsect = magicbox_cf_inb(ioaddr->nsect_addr);
+ tf->hob_lbal = magicbox_cf_inb(ioaddr->lbal_addr);
+ tf->hob_lbam = magicbox_cf_inb(ioaddr->lbam_addr);
+ tf->hob_lbah = magicbox_cf_inb(ioaddr->lbah_addr);
+ magicbox_cf_outb(ioaddr->ctl_addr, tf->ctl);
+ ap->last_ctl = tf->ctl;
+ VPRINTK("hob: feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n",
+ tf->feature,
+ tf->nsect,
+ tf->lbal,
+ tf->lbam,
+ tf->lbah);
+ }
+}
+
+static unsigned int magicbox_cf_data_xfer(struct ata_device *dev,
+ unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ struct ata_port *ap = dev->link->ap;
+ unsigned int words = buflen >> 1;
+ unsigned int i;
+ u16 *buf16 = (u16 *) buf;
+ void __iomem *mmio = ap->ioaddr.data_addr;
+
+ /* Transfer multiple of 2 bytes */
+ if (rw == READ)
+ for (i = 0; i < words; i++)
+ buf16[i] = readw(mmio);
+ else
+ for (i = 0; i < words; i++)
+ writew(buf16[i], mmio);
+
+ /* Transfer trailing 1 byte, if any. */
+ if (unlikely(buflen & 0x01)) {
+ u16 align_buf[1] = { 0 };
+ unsigned char *trailing_buf = buf + buflen - 1;
+
+ if (rw == READ) {
+ align_buf[0] = readw(mmio);
+ memcpy(trailing_buf, align_buf, 1);
+ } else {
+ memcpy(align_buf, trailing_buf, 1);
+ writew(align_buf[0], mmio);
+ }
+ words++;
+ }
+
+ return words << 1;
+}
+
+static void magicbox_cf_irq_on(struct ata_port *ap)
+{
+ /* Nothing to do. */
+}
+
+static void magicbox_cf_irq_clear(struct ata_port *ap)
+{
+ /* Nothing to do. */
+}
+
+static struct ata_port_operations magicbox_cf_port_ops = {
+ .inherits = &ata_sff_port_ops,
+
+ .cable_detect = ata_cable_40wire,
+ .set_mode = magicbox_cf_set_mode,
+
+ .sff_exec_command = magicbox_cf_exec_command,
+ .sff_check_status = magicbox_cf_check_status,
+ .sff_check_altstatus = magicbox_cf_check_altstatus,
+ .sff_dev_select = magicbox_cf_dev_select,
+ .sff_tf_load = magicbox_cf_tf_load,
+ .sff_tf_read = magicbox_cf_tf_read,
+ .sff_data_xfer = magicbox_cf_data_xfer,
+
+ .sff_irq_on = magicbox_cf_irq_on,
+ .sff_irq_clear = magicbox_cf_irq_clear,
+
+ .port_start = ATA_OP_NULL,
+};
+
+static struct scsi_host_template magicbox_cf_sht = {
+ ATA_PIO_SHT(DRV_NAME),
+};
+
+static inline void magicbox_cf_setup_port(struct ata_host *host)
+{
+ struct magicbox_cf_info *info = host->private_data;
+ struct ata_port *ap;
+
+ ap = host->ports[0];
+
+ ap->ops = &magicbox_cf_port_ops;
+ ap->pio_mask = ATA_PIO4;
+ ap->flags |= ATA_FLAG_NO_ATAPI;
+
+ ap->ioaddr.cmd_addr = info->base + MAGICBOX_CF_REG_CMD;
+ ap->ioaddr.data_addr = info->base + MAGICBOX_CF_REG_DATA;
+ ap->ioaddr.error_addr = info->base + MAGICBOX_CF_REG_ERR;
+ ap->ioaddr.feature_addr = info->base + MAGICBOX_CF_REG_FEATURE;
+ ap->ioaddr.nsect_addr = info->base + MAGICBOX_CF_REG_NSECT;
+ ap->ioaddr.lbal_addr = info->base + MAGICBOX_CF_REG_LBAL;
+ ap->ioaddr.lbam_addr = info->base + MAGICBOX_CF_REG_LBAM;
+ ap->ioaddr.lbah_addr = info->base + MAGICBOX_CF_REG_LBAH;
+ ap->ioaddr.device_addr = info->base + MAGICBOX_CF_REG_DEVICE;
+ ap->ioaddr.status_addr = info->base + MAGICBOX_CF_REG_STATUS;
+ ap->ioaddr.command_addr = info->base + MAGICBOX_CF_REG_CMD;
+
+ ap->ioaddr.altstatus_addr = info->ctrl + MAGICBOX_CF_REG_ALTSTATUS;
+ ap->ioaddr.ctl_addr = info->ctrl + MAGICBOX_CF_REG_CTL;
+
+ ata_port_desc(ap, "cmd 0x%p ctl 0x%p", ap->ioaddr.cmd_addr,
+ ap->ioaddr.ctl_addr);
+}
+
+static int __devinit magicbox_cf_of_probe(struct platform_device *op)
+{
+ struct magicbox_cf_info *info;
+ struct ata_host *host;
+ int irq;
+ int ret = 0;
+
+ info = kzalloc(sizeof(struct magicbox_cf_info), GFP_KERNEL);
+ if (info == NULL) {
+ ret = -ENOMEM;
+ goto err_exit;
+ }
+
+ irq = irq_of_parse_and_map(op->dev.of_node, 0);
+ if (irq < 0) {
+ dev_err(&op->dev, "invalid irq\n");
+ ret = -EINVAL;
+ goto err_free_info;
+ }
+
+ info->base = of_iomap(op->dev.of_node, 0);
+ if (info->base == NULL) {
+ ret = -ENOMEM;
+ goto err_free_info;
+ }
+
+ info->ctrl = of_iomap(op->dev.of_node, 1);
+ if (info->ctrl == NULL) {
+ ret = -ENOMEM;
+ goto err_unmap_base;
+ }
+
+ host = ata_host_alloc(&op->dev, MAGICBOX_CF_MAXPORTS);
+ if (host == NULL) {
+ ret = -ENOMEM;
+ goto err_unmap_ctrl;
+ }
+
+ host->private_data = info;
+ magicbox_cf_setup_port(host);
+
+ ret = ata_host_activate(host, irq, ata_sff_interrupt,
+ IRQF_TRIGGER_RISING, &magicbox_cf_sht);
+ if (ret)
+ goto err_unmap_ctrl;
+
+ dev_set_drvdata(&op->dev, host);
+ return 0;
+
+ err_unmap_ctrl:
+ iounmap(info->ctrl);
+ err_unmap_base:
+ iounmap(info->base);
+ err_free_info:
+ kfree(info);
+ err_exit:
+ return ret;
+}
+
+static __devexit int magicbox_cf_of_remove(struct platform_device *op)
+{
+ struct ata_host *host = dev_get_drvdata(&op->dev);
+ struct magicbox_cf_info *info = host->private_data;
+
+ ata_host_detach(host);
+ iounmap(info->ctrl);
+ iounmap(info->base);
+ kfree(info);
+
+ return 0;
+}
+
+static struct of_device_id magicbox_cf_of_match[] = {
+ { .compatible = "pata-magicbox-cf", },
+ {},
+};
+
+static struct platform_driver magicbox_cf_of_platform_driver = {
+ .probe = magicbox_cf_of_probe,
+ .remove = __devexit_p(magicbox_cf_of_remove),
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+ .of_match_table = magicbox_cf_of_match,
+ },
+};
+
+static int __init magicbox_cf_init(void)
+{
+ return platform_driver_register(&magicbox_cf_of_platform_driver);
+}
+
+static void __exit magicbox_cf_exit(void)
+{
+ platform_driver_unregister(&magicbox_cf_of_platform_driver);
+}
+
+module_init(magicbox_cf_init);
+module_exit(magicbox_cf_exit);
+
+MODULE_DESCRIPTION(DRV_DESC);
+MODULE_AUTHOR("Gabor Juhos <juhosg@openwrt.org>");
+MODULE_LICENSE("GPL v2");
+MODULE_VERSION(DRV_VERSION);
+MODULE_DEVICE_TABLE(of, magicbox_cf_of_match);

@ -0,0 +1,55 @@
--- a/arch/powerpc/boot/dts/kilauea.dts
+++ b/arch/powerpc/boot/dts/kilauea.dts
@@ -102,8 +102,8 @@
compatible = "ibm,sdram-405ex", "ibm,sdram-4xx-ddr2";
dcr-reg = <0x010 0x002>;
interrupt-parent = <&UIC2>;
- interrupts = <0x5 0x4 /* ECC DED Error */
- 0x6 0x4>; /* ECC SEC Error */
+ interrupts = <0x5 0x4 /* ECC DED Error */
+ 0x6 0x4>; /* ECC SEC Error */
};
CRYPTO: crypto@ef700000 {
@@ -157,30 +157,30 @@
reg = <0x00000000 0x00000000 0x04000000>;
#address-cells = <1>;
#size-cells = <1>;
- partition@0 {
+ partition0@0 {
label = "kernel";
reg = <0x00000000 0x001e0000>;
};
- partition@1e0000 {
+ partition1@1e0000 {
label = "dtb";
reg = <0x001e0000 0x00020000>;
};
- partition@200000 {
- label = "root";
- reg = <0x00200000 0x00200000>;
- };
- partition@400000 {
- label = "user";
- reg = <0x00400000 0x03b60000>;
+ partition2@200000 {
+ label = "rootfs";
+ reg = <0x00200000 0x03d60000>;
};
- partition@3f60000 {
+ partition3@3f60000 {
label = "env";
reg = <0x03f60000 0x00040000>;
};
- partition@3fa0000 {
+ partition4@3fa0000 {
label = "u-boot";
reg = <0x03fa0000 0x00060000>;
};
+ partition5@0 {
+ label = "firmware";
+ reg = <0x00000000 0x03f60000>;
+ };
};
ndfc@1,0 {

@ -0,0 +1,290 @@
--- a/drivers/usb/host/isp116x-hcd.c
+++ b/drivers/usb/host/isp116x-hcd.c
@@ -1534,6 +1534,7 @@ static struct hc_driver isp116x_hc_drive
/*----------------------------------------------------------------*/
+#ifdef CONFIG_USB_ISP116X_HCD_PLATFORM
static int isp116x_remove(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
@@ -1710,4 +1711,251 @@ static struct platform_driver isp116x_dr
},
};
-module_platform_driver(isp116x_driver);
+static inline int isp116x_platform_register(void)
+{
+ return platform_driver_register(&isp116x_driver);
+}
+
+static inline void isp116x_platform_unregister(void)
+{
+ platform_driver_unregister(&isp116x_driver);
+}
+#else
+static inline int isp116x_platform_register(void) { return 0; };
+static void isp116x_platform_unregister(void) {};
+#endif /* CONFIG_USB_ISP116X_PLATFORM */
+
+/*-----------------------------------------------------------------*/
+
+#ifdef CONFIG_USB_ISP116X_HCD_OF
+
+/* TODO: rework platform probe instead of using a separate probe */
+
+#include <linux/of_platform.h>
+
+#ifdef USE_PLATFORM_DELAY
+static void isp116x_of_delay(struct device *ddev, int delay)
+{
+ ndelay(delay);
+}
+#else
+#define isp116x_of_delay NULL
+#endif
+
+static int __devinit isp116x_of_probe(struct platform_device *op)
+{
+ struct device_node *dn = op->dev.of_node;
+ struct usb_hcd *hcd;
+ struct isp116x *isp116x;
+ struct resource addr, data;
+ struct isp116x_platform_data *board;
+ void __iomem *addr_reg;
+ void __iomem *data_reg;
+ int irq;
+ int ret = 0;
+ unsigned long irqflags;
+
+ ret = of_address_to_resource(dn, 0, &data);
+ if (ret)
+ return ret;
+
+ ret = of_address_to_resource(dn, 1, &addr);
+ if (ret)
+ return ret;
+
+ board = kzalloc(sizeof(struct isp116x_platform_data), GFP_KERNEL);
+ if (board == NULL)
+ return -ENOMEM;
+
+ if (!request_mem_region(addr.start, resource_size(&addr), hcd_name)) {
+ ret = -EBUSY;
+ goto err_free_board;
+ }
+
+ addr_reg = ioremap_nocache(addr.start, resource_size(&addr));
+ if (addr_reg == NULL) {
+ ret = -ENOMEM;
+ goto err_release_addr;
+ }
+
+ if (!request_mem_region(data.start, resource_size(&data), hcd_name)) {
+ ret = -EBUSY;
+ goto err_unmap_addr;
+ }
+
+ data_reg = ioremap_nocache(data.start, resource_size(&data));
+ if (data_reg == NULL) {
+ ret = -ENOMEM;
+ goto err_release_data;
+ }
+
+ irq = irq_of_parse_and_map(dn, 0);
+ if (irq == NO_IRQ) {
+ ret = -EINVAL;
+ goto err_unmap_data;
+ }
+
+ /* allocate and initialize hcd */
+ hcd = usb_create_hcd(&isp116x_hc_driver, &op->dev, dev_name(&op->dev));
+ if (!hcd) {
+ ret = -ENOMEM;
+ goto err_irq_dispose;
+ }
+
+ /* this rsrc_start is bogus */
+ hcd->rsrc_start = addr.start;
+ isp116x = hcd_to_isp116x(hcd);
+ isp116x->data_reg = data_reg;
+ isp116x->addr_reg = addr_reg;
+ isp116x->board = board;
+ spin_lock_init(&isp116x->lock);
+ INIT_LIST_HEAD(&isp116x->async);
+
+ board->delay = isp116x_of_delay;
+ if (of_get_property(dn, "sel15Kres", NULL))
+ board->sel15Kres = 1;
+ if (of_get_property(dn, "oc_enable", NULL))
+ board->oc_enable = 1;
+ if (of_get_property(dn, "remote_wakeup_enable", NULL))
+ board->remote_wakeup_enable = 1;
+
+ if (of_get_property(dn, "int_act_high", NULL))
+ board->int_act_high = 1;
+ if (of_get_property(dn, "int_edge_triggered", NULL))
+ board->int_edge_triggered = 1;
+
+ if (board->int_edge_triggered)
+ irqflags = board->int_act_high ? IRQF_TRIGGER_RISING :
+ IRQF_TRIGGER_FALLING;
+ else
+ irqflags = board->int_act_high ? IRQF_TRIGGER_HIGH :
+ IRQF_TRIGGER_LOW;
+
+ ret = usb_add_hcd(hcd, irq, irqflags | IRQF_DISABLED);
+ if (ret)
+ goto err_put_hcd;
+
+ ret = create_debug_file(isp116x);
+ if (ret) {
+ ERR("Couldn't create debugfs entry\n");
+ goto err_remove_hcd;
+ }
+
+ return 0;
+
+ err_remove_hcd:
+ usb_remove_hcd(hcd);
+ err_put_hcd:
+ usb_put_hcd(hcd);
+ err_irq_dispose:
+ irq_dispose_mapping(irq);
+ err_unmap_data:
+ iounmap(data_reg);
+ err_release_data:
+ release_mem_region(data.start, resource_size(&data));
+ err_unmap_addr:
+ iounmap(addr_reg);
+ err_release_addr:
+ release_mem_region(addr.start, resource_size(&addr));
+ err_free_board:
+ kfree(board);
+ return ret;
+}
+
+static __devexit int isp116x_of_remove(struct platform_device *op)
+{
+ struct usb_hcd *hcd = dev_get_drvdata(&op->dev);
+ struct isp116x *isp116x;
+ struct resource res;
+
+ if (!hcd)
+ return 0;
+
+ dev_set_drvdata(&op->dev, NULL);
+
+ isp116x = hcd_to_isp116x(hcd);
+ remove_debug_file(isp116x);
+ usb_remove_hcd(hcd);
+
+ irq_dispose_mapping(hcd->irq);
+
+ iounmap(isp116x->data_reg);
+ (void) of_address_to_resource(op->dev.of_node, 0, &res);
+ release_mem_region(res.start, resource_size(&res));
+
+ iounmap(isp116x->addr_reg);
+ (void) of_address_to_resource(op->dev.of_node, 1, &res);
+ release_mem_region(res.start, resource_size(&res));
+
+ kfree(isp116x->board);
+ usb_put_hcd(hcd);
+
+ return 0;
+}
+
+static struct of_device_id isp116x_of_match[] = {
+ { .compatible = "isp116x-hcd", },
+ {},
+};
+
+static struct platform_driver isp116x_of_platform_driver = {
+ .probe = isp116x_of_probe,
+ .remove = __devexit_p(isp116x_of_remove),
+ .driver = {
+ .name = "isp116x-hcd-of",
+ .owner = THIS_MODULE,
+ .of_match_table = isp116x_of_match,
+ },
+};
+
+static int __init isp116x_of_register(void)
+{
+ return platform_driver_register(&isp116x_of_platform_driver);
+}
+
+static void __exit isp116x_of_unregister(void)
+{
+ platform_driver_unregister(&isp116x_of_platform_driver);
+}
+
+MODULE_DEVICE_TABLE(of, isp116x_of_match);
+
+#else
+static inline int isp116x_of_register(void) { return 0; };
+static void isp116x_of_unregister(void) {};
+#endif /* CONFIG_USB_ISP116X_HCD_OF */
+
+/*-----------------------------------------------------------------*/
+
+static int __init isp116x_init(void)
+{
+ int ret;
+
+ if (usb_disabled())
+ return -ENODEV;
+
+ INFO("driver %s, %s\n", hcd_name, DRIVER_VERSION);
+ ret = isp116x_platform_register();
+ if (ret)
+ return ret;
+
+ ret = isp116x_of_register();
+ if (ret)
+ goto err_platform_unregister;
+
+ return 0;
+
+ err_platform_unregister:
+ isp116x_platform_unregister();
+ return ret;
+}
+
+module_init(isp116x_init);
+
+static void __exit isp116x_cleanup(void)
+{
+ isp116x_of_unregister();
+ isp116x_platform_unregister();
+}
+
+module_exit(isp116x_cleanup);
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -260,6 +260,24 @@ config USB_ISP116X_HCD
To compile this driver as a module, choose M here: the
module will be called isp116x-hcd.
+config USB_ISP116X_HCD_PLATFORM
+ bool "ISP116X support for controllers on platform bus"
+ depends on USB_ISP116X_HCD
+ default n if PPC_OF
+ default y
+ ---help---
+ Enables support for the ISP116x USB controller present on the
+ platform bus.
+
+config USB_ISP116X_HCD_OF
+ bool "ISP116X support for controllers on OF platform bus"
+ depends on USB_ISP116X_HCD && PPC_OF
+ default y if PPC_OF
+ default n
+ ---help---
+ Enables support for the ISP116x USB controller present on the
+ OpenFirmware platform bus.
+
config USB_ISP1760_HCD
tristate "ISP 1760 HCD support"
depends on USB && EXPERIMENTAL

@ -0,0 +1,111 @@
--- a/drivers/usb/host/isp116x.h
+++ b/drivers/usb/host/isp116x.h
@@ -364,22 +364,64 @@ struct isp116x_ep {
#define IRQ_TEST() do{}while(0)
#endif
+#ifdef CONFIG_405EP
+static inline void isp116x_writew(u16 val, void __iomem *addr)
+{
+ writew(cpu_to_le16(val), addr);
+}
+
+static inline u16 isp116x_readw(void __iomem *addr)
+{
+ return le16_to_cpu(readw(addr));
+}
+
+static inline void isp116x_raw_writew(u16 val, void __iomem *addr)
+{
+ writew(cpu_to_le16(val), addr);
+}
+
+static inline u16 isp116x_raw_readw(void __iomem *addr)
+{
+ return le16_to_cpu(readw(addr));
+}
+#else
+static inline void isp116x_writew(u16 val, void __iomem *addr)
+{
+ writew(val, addr);
+}
+
+static inline u16 isp116x_readw(void __iomem *addr)
+{
+ return readw(addr);
+}
+
+static inline void isp116x_raw_writew(u16 val, void __iomem *addr)
+{
+ __raw_writew(val, addr);
+}
+
+static inline u16 isp116x_raw_readw(void __iomem *addr)
+{
+ return __raw_readw(addr);
+}
+#endif
+
static inline void isp116x_write_addr(struct isp116x *isp116x, unsigned reg)
{
IRQ_TEST();
- writew(reg & 0xff, isp116x->addr_reg);
+ isp116x_writew(reg & 0xff, isp116x->addr_reg);
isp116x_delay(isp116x, 300);
}
static inline void isp116x_write_data16(struct isp116x *isp116x, u16 val)
{
- writew(val, isp116x->data_reg);
+ isp116x_writew(val, isp116x->data_reg);
isp116x_delay(isp116x, 150);
}
static inline void isp116x_raw_write_data16(struct isp116x *isp116x, u16 val)
{
- __raw_writew(val, isp116x->data_reg);
+ isp116x_raw_writew(val, isp116x->data_reg);
isp116x_delay(isp116x, 150);
}
@@ -387,7 +429,7 @@ static inline u16 isp116x_read_data16(st
{
u16 val;
- val = readw(isp116x->data_reg);
+ val = isp116x_readw(isp116x->data_reg);
isp116x_delay(isp116x, 150);
return val;
}
@@ -396,16 +438,16 @@ static inline u16 isp116x_raw_read_data1
{
u16 val;
- val = __raw_readw(isp116x->data_reg);
+ val = isp116x_raw_readw(isp116x->data_reg);
isp116x_delay(isp116x, 150);
return val;
}
static inline void isp116x_write_data32(struct isp116x *isp116x, u32 val)
{
- writew(val & 0xffff, isp116x->data_reg);
+ isp116x_writew(val & 0xffff, isp116x->data_reg);
isp116x_delay(isp116x, 150);
- writew(val >> 16, isp116x->data_reg);
+ isp116x_writew(val >> 16, isp116x->data_reg);
isp116x_delay(isp116x, 150);
}
@@ -413,9 +455,9 @@ static inline u32 isp116x_read_data32(st
{
u32 val;
- val = (u32) readw(isp116x->data_reg);
+ val = (u32) isp116x_readw(isp116x->data_reg);
isp116x_delay(isp116x, 150);
- val |= ((u32) readw(isp116x->data_reg)) << 16;
+ val |= ((u32) isp116x_readw(isp116x->data_reg)) << 16;
isp116x_delay(isp116x, 150);
return val;
}
Loading…
Cancel
Save