remove 2.6.27 patches

SVN-Revision: 16894

target/linux/au1000/patches-2.6.27/001-mtx1_cmdline.patch

@@ -1,11 +0,0 @@
---- a/arch/mips/au1000/mtx-1/init.c
-+++ b/arch/mips/au1000/mtx-1/init.c
-@@ -49,7 +49,7 @@ void __init prom_init(void)
- 	prom_argv = (char **)fw_arg1;
- 	prom_envp = (char **)fw_arg2;
- 
--	prom_init_cmdline();
-+	strcpy(arcs_cmdline, CONFIG_CMDLINE);
- 
- 	memsize_str = prom_getenv("memsize");
- 	if (!memsize_str)

target/linux/au1000/patches-2.6.27/002-openwrt_rootfs.patch

@@ -1,11 +0,0 @@
---- a/arch/mips/au1000/mtx-1/platform.c
-+++ b/arch/mips/au1000/mtx-1/platform.c
-@@ -90,7 +90,7 @@ static struct platform_device mtx1_gpio_
- 
- static struct mtd_partition mtx1_mtd_partitions[] = {
- 	{
--		.name	= "filesystem",
-+		.name	= "rootfs",
- 		.size	= 0x01C00000,
- 		.offset	= 0,
- 	},

target/linux/au1000/patches-2.6.27/003-au1000_eth_ioctl.patch

@@ -1,15 +0,0 @@
---- a/drivers/net/au1000_eth.c
-+++ b/drivers/net/au1000_eth.c
-@@ -1293,9 +1293,12 @@ static void set_rx_mode(struct net_devic
- 	}
- }
- 
-+#define AU1000_KNOWN_PHY_IOCTLS 		(SIOCGMIIPHY & 0xfff0)
- static int au1000_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
- {
- 	struct au1000_private *aup = (struct au1000_private *)dev->priv;
-+	if((cmd & AU1000_KNOWN_PHY_IOCTLS) != AU1000_KNOWN_PHY_IOCTLS)
-+		return -EINVAL;
- 
- 	if (!netif_running(dev)) return -EINVAL;
- 

target/linux/au1000/patches-2.6.27/004-state_led_phy_fix.patch

@@ -1,31 +0,0 @@
---- a/drivers/net/au1000_eth.c
-+++ b/drivers/net/au1000_eth.c
-@@ -184,6 +184,15 @@ struct au1000_private *au_macs[NUM_ETH_I
- #  undef AU1XXX_PHY1_IRQ
- #endif
- 
-+#if defined(CONFIG_MIPS_MTX1)
-+/*
-+ * 4G MeshCube (MTX-1) board
-+ * PHY is at address 31 on MAC0
-+ * autodetect fails if not searched for highest address !
-+ */
-+# define AU1XXX_PHY_SEARCH_HIGHEST_ADDR
-+#endif
-+
- #if defined(AU1XXX_PHY0_BUSID) && (AU1XXX_PHY0_BUSID > 0)
- # error MAC0-associated PHY attached 2nd MACs MII bus not supported yet
- #endif
-@@ -380,6 +389,12 @@ static int mii_probe (struct net_device 
- 	aup->old_duplex = -1;
- 	aup->phy_dev = phydev;
- 
-+#ifdef CONFIG_MIPS_MTX1
-+	/* set up ethernet jack LEDs on the 4G MeshCube (MTX-1 board) */
-+	printk(KERN_INFO "MTX-1 PHY: updating LED settings\n");
-+	phy_write(phydev, 0x11, 0xff80);
-+#endif
-+
- 	printk(KERN_INFO "%s: attached PHY driver [%s] "
- 	       "(mii_bus:phy_addr=%s, irq=%d)\n",
- 	       dev->name, phydev->drv->name, phydev->dev.bus_id, phydev->irq);

target/linux/au1000/patches-2.6.27/005-mtx1_wdt_fix.patch

@@ -1,20 +0,0 @@
---- a/drivers/watchdog/mtx-1_wdt.c
-+++ b/drivers/watchdog/mtx-1_wdt.c
-@@ -98,6 +98,8 @@ static void mtx1_wdt_reset(void)
- 
- static void mtx1_wdt_start(void)
- {
-+	unsigned long flags;
-+
- 	spin_lock_irqsave(&mtx1_wdt_device.lock, flags);
- 	if (!mtx1_wdt_device.queue) {
- 		mtx1_wdt_device.queue = 1;
-@@ -110,6 +112,8 @@ static void mtx1_wdt_start(void)
- 
- static int mtx1_wdt_stop(void)
- {
-+	unsigned long flags;
-+
- 	spin_lock_irqsave(&mtx1_wdt_device.lock, flags);
- 	if (mtx1_wdt_device.queue) {
- 		mtx1_wdt_device.queue = 0;

target/linux/au1000/patches-2.6.27/006-missing_string_header.patch

@@ -1,10 +0,0 @@
---- a/arch/mips/au1000/mtx-1/init.c
-+++ b/arch/mips/au1000/mtx-1/init.c
-@@ -32,6 +32,7 @@
- #include <linux/init.h>
- 
- #include <asm/bootinfo.h>
-+#include <asm/string.h>
- 
- #include <prom.h>
- 

target/linux/au1000/patches-2.6.27/007-gpiolib.patch

@@ -1,396 +0,0 @@
---- a/arch/mips/au1000/Kconfig
-+++ b/arch/mips/au1000/Kconfig
-@@ -134,3 +134,4 @@ config SOC_AU1X00
- 	select SYS_HAS_CPU_MIPS32_R1
- 	select SYS_SUPPORTS_32BIT_KERNEL
- 	select SYS_SUPPORTS_APM_EMULATION
-+	select ARCH_REQUIRE_GPIOLIB
---- a/arch/mips/au1000/common/gpio.c
-+++ b/arch/mips/au1000/common/gpio.c
-@@ -1,5 +1,5 @@
- /*
-- *  Copyright (C) 2007, OpenWrt.org, Florian Fainelli <florian@openwrt.org>
-+ *  Copyright (C) 2007-2008, OpenWrt.org, Florian Fainelli <florian@openwrt.org>
-  *  	Architecture specific GPIO support
-  *
-  *  This program is free software; you can redistribute	 it and/or modify it
-@@ -27,122 +27,222 @@
-  * 	others have a second one : GPIO2
-  */
- 
-+#include <linux/kernel.h>
- #include <linux/module.h>
-+#include <linux/types.h>
-+#include <linux/platform_device.h>
-+#include <linux/gpio.h>
- 
- #include <asm/mach-au1x00/au1000.h>
--#include <asm/gpio.h>
-+#include <asm/mach-au1x00/gpio.h>
- 
--#define gpio1 sys
--#if !defined(CONFIG_SOC_AU1000)
-+struct au1000_gpio_chip {
-+	struct gpio_chip	chip;
-+	void __iomem		*regbase;
-+};
- 
--static struct au1x00_gpio2 *const gpio2 = (struct au1x00_gpio2 *) GPIO2_BASE;
-+#if !defined(CONFIG_SOC_AU1000)
- #define GPIO2_OUTPUT_ENABLE_MASK 	0x00010000
- 
--static int au1xxx_gpio2_read(unsigned gpio)
-+/*
-+ * Return GPIO bank 2 level
-+ */
-+static int au1000_gpio2_get(struct gpio_chip *chip, unsigned offset)
- {
--	gpio -= AU1XXX_GPIO_BASE;
--	return ((gpio2->pinstate >> gpio) & 0x01);
-+	u32 mask = 1 << offset;
-+	struct au1000_gpio_chip	*gpch;
-+	
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	return readl(gpch->regbase + AU1000_GPIO2_ST) & mask;
- }
- 
--static void au1xxx_gpio2_write(unsigned gpio, int value)
-+/*
-+ * Set output GPIO bank 2 level
-+ */
-+static void au1000_gpio2_set(struct gpio_chip *chip,
-+				unsigned offset, int value)
- {
--	gpio -= AU1XXX_GPIO_BASE;
--
--	gpio2->output = (GPIO2_OUTPUT_ENABLE_MASK << gpio) | ((!!value) << gpio);
-+	u32			mask = (!!value) << offset;
-+	struct au1000_gpio_chip	*gpch;
-+	unsigned long		flags;
-+
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	
-+	local_irq_save(flags);
-+	writel((GPIO2_OUTPUT_ENABLE_MASK << offset) | mask,
-+				gpch->regbase + AU1000_GPIO2_OUT);
-+	local_irq_restore(flags);
- }
- 
--static int au1xxx_gpio2_direction_input(unsigned gpio)
-+/*
-+ * Set GPIO bank 2 direction to input
-+ */
-+static int au1000_gpio2_direction_input(struct gpio_chip *chip, unsigned offset)
- {
--	gpio -= AU1XXX_GPIO_BASE;
--	gpio2->dir &= ~(0x01 << gpio);
-+	unsigned long 		flags;
-+	u32			mask = 1 << offset;
-+	u32			value;
-+	struct au1000_gpio_chip	*gpch;
-+	void __iomem		*gpdr;
-+
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	gpdr = gpch->regbase + AU1000_GPIO2_DIR;
-+
-+	local_irq_save(flags);
-+	value = readl(gpdr);
-+	value &= ~mask;
-+	writel(value, gpdr);
-+	local_irq_restore(flags);
-+
- 	return 0;
- }
- 
--static int au1xxx_gpio2_direction_output(unsigned gpio, int value)
-+/*
-+ * Set GPIO bank2 direction to output
-+ */
-+static int au1000_gpio2_direction_output(struct gpio_chip *chip,
-+					unsigned offset, int value)
- {
--	gpio -= AU1XXX_GPIO_BASE;
--	gpio2->dir |= 0x01 << gpio;
--	gpio2->output = (GPIO2_OUTPUT_ENABLE_MASK << gpio) | ((!!value) << gpio);
-+	unsigned long		flags;
-+	u32			mask = 1 << offset;
-+	u32			tmp;
-+	struct au1000_gpio_chip	*gpch;
-+	void __iomem		*gpdr;
-+	
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	gpdr = gpch->regbase + AU1000_GPIO2_DIR;
-+	
-+	local_irq_save(flags);
-+	tmp = readl(gpdr);
-+	tmp |= mask;
-+	writel(tmp, gpdr);
-+	mask = (!!value) << offset;
-+        writel((GPIO2_OUTPUT_ENABLE_MASK << offset) | mask,
-+	                                gpch->regbase + AU1000_GPIO2_OUT);
-+	local_irq_restore(flags);
-+
- 	return 0;
- }
--
- #endif /* !defined(CONFIG_SOC_AU1000) */
- 
--static int au1xxx_gpio1_read(unsigned gpio)
-+/*
-+ * Return GPIO bank 2 level
-+ */
-+static int au1000_gpio1_get(struct gpio_chip *chip, unsigned offset)
- {
--	return (gpio1->pinstaterd >> gpio) & 0x01;
-+	u32			mask = 1 << offset;
-+	struct au1000_gpio_chip	*gpch;
-+
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	return readl(gpch->regbase + 0x0110) & mask;
- }
- 
--static void au1xxx_gpio1_write(unsigned gpio, int value)
-+/*
-+ * Set GPIO bank 1 level
-+ */
-+static void au1000_gpio1_set(struct gpio_chip *chip,
-+				unsigned offset, int value)
- {
-+	unsigned long		flags;
-+	u32			mask = 1 << offset;
-+	struct au1000_gpio_chip	*gpch;
-+
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	
-+	local_irq_save(flags);
- 	if (value)
--		gpio1->outputset = (0x01 << gpio);
-+		writel(mask, gpch->regbase + 0x0108);	
- 	else
--		/* Output a zero */
--		gpio1->outputclr = (0x01 << gpio);
-+		writel(mask, gpch->regbase + 0x010C);
-+	local_irq_restore(flags);
- }
- 
--static int au1xxx_gpio1_direction_input(unsigned gpio)
-+/*
-+ * Set GPIO bank 1 direction to input
-+ */
-+static int au1000_gpio1_direction_input(struct gpio_chip *chip, unsigned offset)
- {
--	gpio1->pininputen = (0x01 << gpio);
--	return 0;
--}
-+	unsigned long		flags;
-+	u32			mask = 1 << offset;
-+	u32			value;
-+	struct au1000_gpio_chip	*gpch;
-+	void __iomem		*gpdr;
-+
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	gpdr = gpch->regbase + 0x0110;
-+	
-+	local_irq_save(flags);
-+	value = readl(gpdr);
-+	value |= mask;
-+	writel(mask, gpdr);
-+	local_irq_restore(flags);
- 
--static int au1xxx_gpio1_direction_output(unsigned gpio, int value)
--{
--	gpio1->trioutclr = (0x01 & gpio);
--	au1xxx_gpio1_write(gpio, value);
- 	return 0;
- }
- 
--int au1xxx_gpio_get_value(unsigned gpio)
-+/*
-+ * Set GPIO bank 1 direction to output
-+ */
-+static int au1000_gpio1_direction_output(struct gpio_chip *chip,
-+					unsigned offset, int value)
- {
--	if (gpio >= AU1XXX_GPIO_BASE)
--#if defined(CONFIG_SOC_AU1000)
--		return 0;
--#else
--		return au1xxx_gpio2_read(gpio);
--#endif
-+	unsigned long		flags;
-+	u32			mask = 1 << offset;
-+	u32			tmp;
-+	struct au1000_gpio_chip	*gpch;
-+	void __iomem 		*gpdr;
-+
-+	gpch = container_of(chip, struct au1000_gpio_chip, chip);
-+	gpdr = gpch->regbase + 0x0100;
-+	
-+	local_irq_save(flags);
-+	tmp = readl(gpdr);
-+	writel(tmp, gpdr);
-+	if (value)
-+		writel(mask, gpch->regbase + 0x0108);
- 	else
--		return au1xxx_gpio1_read(gpio);
--}
--EXPORT_SYMBOL(au1xxx_gpio_get_value);
-+		writel(mask, gpch->regbase + 0x0108);
-+	local_irq_restore(flags);
- 
--void au1xxx_gpio_set_value(unsigned gpio, int value)
--{
--	if (gpio >= AU1XXX_GPIO_BASE)
--#if defined(CONFIG_SOC_AU1000)
--		;
--#else
--		au1xxx_gpio2_write(gpio, value);
--#endif
--	else
--		au1xxx_gpio1_write(gpio, value);
-+	return 0;
- }
--EXPORT_SYMBOL(au1xxx_gpio_set_value);
- 
--int au1xxx_gpio_direction_input(unsigned gpio)
--{
--	if (gpio >= AU1XXX_GPIO_BASE)
--#if defined(CONFIG_SOC_AU1000)
--		return -ENODEV;
--#else
--		return au1xxx_gpio2_direction_input(gpio);
-+struct au1000_gpio_chip au1000_gpio_chip[] = {
-+	[0] = {
-+		.regbase			= (void __iomem *)SYS_BASE,
-+		.chip = {
-+			.label			= "au1000-gpio1",
-+			.direction_input	= au1000_gpio1_direction_input,
-+			.direction_output	= au1000_gpio1_direction_output,
-+			.get			= au1000_gpio1_get,
-+			.set			= au1000_gpio1_set,
-+			.base			= 0,
-+			.ngpio			= 32,
-+		},
-+	},
-+#if !defined(CONFIG_SOC_AU1000)
-+	[1] = {
-+		.regbase			= (void __iomem *)GPIO2_BASE,
-+		.chip = {
-+			.label			= "au1000-gpio2",
-+			.direction_input	= au1000_gpio2_direction_input,
-+			.direction_output	= au1000_gpio2_direction_output,
-+			.get			= au1000_gpio2_get,
-+			.set			= au1000_gpio2_set,
-+			.base			= AU1XXX_GPIO_BASE,
-+			.ngpio			= 32,
-+		},
-+	},
- #endif
-+};
- 
--	return au1xxx_gpio1_direction_input(gpio);
--}
--EXPORT_SYMBOL(au1xxx_gpio_direction_input);
--
--int au1xxx_gpio_direction_output(unsigned gpio, int value)
-+int __init au1000_gpio_init(void)
- {
--	if (gpio >= AU1XXX_GPIO_BASE)
--#if defined(CONFIG_SOC_AU1000)
--		return -ENODEV;
--#else
--		return au1xxx_gpio2_direction_output(gpio, value);
-+	gpiochip_add(&au1000_gpio_chip[0].chip);
-+#if !defined(CONFIG_SOC_AU1000)
-+	gpiochip_add(&au1000_gpio_chip[1].chip);
- #endif
- 
--	return au1xxx_gpio1_direction_output(gpio, value);
-+	return 0;
- }
--EXPORT_SYMBOL(au1xxx_gpio_direction_output);
-+arch_initcall(au1000_gpio_init);
---- a/include/asm-mips/mach-au1x00/gpio.h
-+++ b/include/asm-mips/mach-au1x00/gpio.h
-@@ -1,69 +1,21 @@
- #ifndef _AU1XXX_GPIO_H_
- #define _AU1XXX_GPIO_H_
- 
--#include <linux/types.h>
--
- #define AU1XXX_GPIO_BASE	200
- 
--struct au1x00_gpio2 {
--	u32	dir;
--	u32	reserved;
--	u32	output;
--	u32	pinstate;
--	u32	inten;
--	u32	enable;
--};
--
--extern int au1xxx_gpio_get_value(unsigned gpio);
--extern void au1xxx_gpio_set_value(unsigned gpio, int value);
--extern int au1xxx_gpio_direction_input(unsigned gpio);
--extern int au1xxx_gpio_direction_output(unsigned gpio, int value);
--
--
--/* Wrappers for the arch-neutral GPIO API */
--
--static inline int gpio_request(unsigned gpio, const char *label)
--{
--	/* Not yet implemented */
--	return 0;
--}
--
--static inline void gpio_free(unsigned gpio)
--{
--	/* Not yet implemented */
--}
--
--static inline int gpio_direction_input(unsigned gpio)
--{
--	return au1xxx_gpio_direction_input(gpio);
--}
--
--static inline int gpio_direction_output(unsigned gpio, int value)
--{
--	return au1xxx_gpio_direction_output(gpio, value);
--}
--
--static inline int gpio_get_value(unsigned gpio)
--{
--	return au1xxx_gpio_get_value(gpio);
--}
--
--static inline void gpio_set_value(unsigned gpio, int value)
--{
--	au1xxx_gpio_set_value(gpio, value);
--}
--
--static inline int gpio_to_irq(unsigned gpio)
--{
--	return gpio;
--}
--
--static inline int irq_to_gpio(unsigned irq)
--{
--	return irq;
--}
-+#define AU1000_GPIO2_DIR	0x00
-+#define AU1000_GPIO2_RSVD	0x04
-+#define AU1000_GPIO2_OUT	0x08
-+#define AU1000_GPIO2_ST		0x0C
-+#define AU1000_GPIO2_INT	0x10
-+#define AU1000_GPIO2_EN		0x14
-+
-+#define gpio_get_value		__gpio_get_value
-+#define gpio_set_value		__gpio_set_value
-+
-+#define gpio_to_irq(gpio)	NULL
-+#define irq_to_gpio(irq)	NULL
- 
--/* For cansleep */
- #include <asm-generic/gpio.h>
- 
- #endif /* _AU1XXX_GPIO_H_ */