You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
freifunkist-firmware/target/linux/ath79/dts/qca9557_buffalo_bhr-4grv2.dts

148 lines
2.4 KiB

// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include "qca9557.dtsi"
/ {
compatible = "buffalo,bhr-4grv2", "qca,qca9557";
model = "Buffalo BHR-4GRV2";
aliases {
led-boot = &power;
led-failsafe = &power;
led-running = &power;
led-upgrade = &power;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
leds {
compatible = "gpio-leds";
power: power {
label = "bhr-4grv2:green:power";
gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
default-state = "on";
};
diag {
label = "bhr-4grv2:orange:diag";
gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
};
vpn_orange {
label = "bhr-4grv2:orange:vpn";
gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
};
vpn_green {
label = "bhr-4grv2:green:vpn";
gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
};
};
keys {
compatible = "gpio-keys-polled";
poll-interval = <20>;
reset {
label = "reset";
gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
debounce-interval = <60>;
};
eco {
label = "eco";
gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
debounce-interval = <60>;
};
};
};
&spi {
status = "okay";
num-cs = <1>;
flash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <25000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "u-boot";
reg = <0x000000 0x040000>;
read-only;
};
partition@40000 {
label = "u-boot-env";
reg = <0x040000 0x010000>;
};
partition@50000 {
ath79: modify mtd partitions for Buffalo BHR-4GRV2 This commit modifies mtd partitions define for Buffalo BHR-4GRV2 and move it to generic subtarget. In Buffalo BHR-4GRV2, "kernel" partition is located behined "rootfs" partition in the stock firmware. This causes the size of the kernel to be limited by the fixed value. 0x50000 0xe80000 0xff0000 +-------------------------------+--------------+ | rootfs | kernel | | (14528k) | (1472k) | +-------------------------------+--------------+ After ar71xx was updated to Kernel 4.14, the kernel size of BHR-4GRV2 exceeded the limit, and it breaks builds on official buildbot. Since this issue was also confirmed in ath79, I modified the mtd partitions to get rid of that limitation. 0x50000 0xff0000 +----------------------------------------------+ | firmware | | (16000k) | +----------------------------------------------+ However, this commit breaks compatibility with ar71xx firmware, so I dropped "SUPPORTED_DEVICES += bhr-4grv2". This commit requires new flash instruction instead of the old one. Flash instruction using initramfs image: 1. Connect the computer to the LAN port of BHR-4GRV2 2. Set the IP address of the computer to 192.168.12.10 3. Rename the OpenWrt initramfs image to "bhr4grv2-uImage-initramfs-gzip.bin" and place it into the TFTP directory 4. Start the tftp server on the computer 5. While holding down the "ECO" button, connect power cable to BHR-4GRV2 and turn on it 6. Flashing (orange) diag LED and release the finger from the button, BHR-4GRV2 downloads the intiramfs image from TFTP server and boot with it 7. On the initramfs image, create "/etc/fw_env.config" file with following contents /dev/mtd1 0x0 0x10000 0x10000 8. Execute following commands to add environment variables for u-boot fw_setenv ipaddr 192.168.12.1 fw_setenv serverip 192.168.12.10 fw_setenv ethaddr 00:aa:bb:cc:dd:ee fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" 9. Perform sysupgrade with squashfs-sysupgrade image 10. Wait ~150 seconds to complete flashing And this commit includes small fix; BHR-4GRV2 has QCA9557 as a SoC, not QCA9558. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
6 years ago
compatible = "denx,uimage";
label = "firmware";
reg = <0x050000 0xfa0000>;
};
art: partition@ff0000 {
label = "art";
reg = <0xff0000 0x010000>;
read-only;
};
};
};
};
&mdio0 {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
qca,ar8327-initvals = <
0x04 0x80080080 /* PORT0 PAD MODE CTRL */
0x0c 0x07600000 /* PORT6 PAD MODE CTRL */
0x7c 0x0000007e /* PORT0_STATUS */
0x94 0x0000007e /* PORT6 STATUS */
>;
};
};
&eth0 {
status = "okay";
mtd-mac-address = <&art 0x0>;
phy-handle = <&phy0>;
pll-data = <0x56000000 0x00000101 0x00001616>;
};
&eth1 {
status = "okay";
mtd-mac-address = <&art 0x6>;
pll-data = <0x03000101 0x00000101 0x00001616>;
fixed-link {
speed = <1000>;
full-duplex;
};
};
&uart {
status = "okay";
};