You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
freifunkist-firmware/target/linux/brcm2708/patches-4.14/950-0161-ASoC-bcm2835-fix-h...

70 lines
2.1 KiB

brcm2708: add kernel 4.14 support Patch generation process: - rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable - git format-patch v4.14.89 Patches skipped during rebase: - lan78xx: Read MAC address from DT if present - lan78xx: Enable LEDs and auto-negotiation - Revert "softirq: Let ksoftirqd do its job" - sc16is7xx: Fix for multi-channel stall - lan78xx: Ignore DT MAC address if already valid - lan78xx: Simple patch to prevent some crashes - tcp_write_queue_purge clears all the SKBs in the write queue - Revert "lan78xx: Simple patch to prevent some crashes" - lan78xx: Connect phy early - Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro - Revert "Revert "softirq: Let ksoftirqd do its job"" - ASoC: cs4265: SOC_SINGLE register value error fix - Revert "ASoC: cs4265: SOC_SINGLE register value error fix" - Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends" - Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"" Patches dropped after rebase: - net: Add non-mainline source for rtl8192cu wlan - net: Fix rtl8192cu build errors on other platforms - brcm: adds support for BCM43341 wifi - brcmfmac: Mute expected startup 'errors' - ARM64: Fix build break for RTL8187/RTL8192CU wifi - ARM64: Enable RTL8187/RTL8192CU wifi in build config - This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator - brcmfmac: add CLM download support - brcmfmac: request_firmware_direct is quieter - Sets the BCDC priority to constant 0 - brcmfmac: Disable ARP offloading when promiscuous - brcmfmac: Avoid possible out-of-bounds read - brcmfmac: Delete redundant length check - net: rtl8192cu: Normalize indentation - net: rtl8192cu: Fix implicit fallthrough warnings - Revert "Sets the BCDC priority to constant 0" - media: cxd2880: Bump to match 4.18.y version - media: cxd2880-spi: Bump to match 4.18.y version - Revert "mm: alloc_contig: re-allow CMA to compact FS pages" - Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages"" - cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with MEDIA_SUBDRV_AUTOSELECT - 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch - 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch Make I2C built-in instead of modular as in upstream defconfig; also the easiest way to get MFD_ARIZONA enabled, which is required by kmod-sound-soc-rpi-cirrus. Add missing compatible strings from 4.9/960-add-rasbperrypi-compatible.patch, using upstream names for compute modules. Add extra patch to enable the LEDs on lan78xx. Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y) Runtime-tested: bcm2708, bcm2710 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years ago
From 0f409e6c30a04eb85792a6883e81ad2af118c7bd Mon Sep 17 00:00:00 2001
From: Matthias Reichl <github@hias.horus.com>
Date: Thu, 18 Jan 2018 12:36:44 +0100
Subject: [PATCH 161/454] ASoC: bcm2835: fix hw_params error when device is in
prepared state (#2345)
commit 8d5737a5f53902a916ee1e1cb248c9b8b883b2ea upstream.
If bcm2835 is configured as bitclock master calling hw_params()
after prepare() fails with EBUSY. This also makes it impossible to
use bcm2835 in full duplex mode.
The error is caused by the split clock setup: clk_set_rate
is called in hw_params, clk_prepare_enable in prepare. As hw_params
doesn't check if the clock was already enabled clk_set_rate
fails with EBUSY.
Fix this by moving clock startup from prepare to hw_params and
let hw_params properly deal with an already set up or enabled
clock.
Signed-off-by: Matthias Reichl <hias@horus.com>
---
sound/soc/bcm/bcm2835-i2s.c | 20 ++++++++++++++------
1 file changed, 14 insertions(+), 6 deletions(-)
--- a/sound/soc/bcm/bcm2835-i2s.c
+++ b/sound/soc/bcm/bcm2835-i2s.c
@@ -130,6 +130,7 @@ struct bcm2835_i2s_dev {
struct regmap *i2s_regmap;
struct clk *clk;
bool clk_prepared;
+ int clk_rate;
};
static void bcm2835_i2s_start_clock(struct bcm2835_i2s_dev *dev)
@@ -419,10 +420,19 @@ static int bcm2835_i2s_hw_params(struct
}
/* Clock should only be set up here if CPU is clock master */
- if (bit_clock_master) {
- ret = clk_set_rate(dev->clk, bclk_rate);
- if (ret)
- return ret;
+ if (bit_clock_master &&
+ (!dev->clk_prepared || dev->clk_rate != bclk_rate)) {
+ if (dev->clk_prepared)
+ bcm2835_i2s_stop_clock(dev);
+
+ if (dev->clk_rate != bclk_rate) {
+ ret = clk_set_rate(dev->clk, bclk_rate);
+ if (ret)
+ return ret;
+ dev->clk_rate = bclk_rate;
+ }
+
+ bcm2835_i2s_start_clock(dev);
}
/* Setup the frame format */
@@ -618,8 +628,6 @@ static int bcm2835_i2s_prepare(struct sn
struct bcm2835_i2s_dev *dev = snd_soc_dai_get_drvdata(dai);
uint32_t cs_reg;
- bcm2835_i2s_start_clock(dev);
-
/*
* Clear both FIFOs if the one that should be started
* is not empty at the moment. This should only happen