You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
freifunkist-firmware/target/linux/brcm2708/patches-4.14/950-0233-overlays-Rework-sd...

157 lines
4.3 KiB

brcm2708: add kernel 4.14 support Patch generation process: - rebase rpi/rpi-4.14.y on v4.14.89 from linux-stable - git format-patch v4.14.89 Patches skipped during rebase: - lan78xx: Read MAC address from DT if present - lan78xx: Enable LEDs and auto-negotiation - Revert "softirq: Let ksoftirqd do its job" - sc16is7xx: Fix for multi-channel stall - lan78xx: Ignore DT MAC address if already valid - lan78xx: Simple patch to prevent some crashes - tcp_write_queue_purge clears all the SKBs in the write queue - Revert "lan78xx: Simple patch to prevent some crashes" - lan78xx: Connect phy early - Arm: mm: ftrace: Only set text back to ro after kernel has been marked ro - Revert "Revert "softirq: Let ksoftirqd do its job"" - ASoC: cs4265: SOC_SINGLE register value error fix - Revert "ASoC: cs4265: SOC_SINGLE register value error fix" - Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends" - Revert "Revert "net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"" Patches dropped after rebase: - net: Add non-mainline source for rtl8192cu wlan - net: Fix rtl8192cu build errors on other platforms - brcm: adds support for BCM43341 wifi - brcmfmac: Mute expected startup 'errors' - ARM64: Fix build break for RTL8187/RTL8192CU wifi - ARM64: Enable RTL8187/RTL8192CU wifi in build config - This is the driver for Sony CXD2880 DVB-T2/T tuner + demodulator - brcmfmac: add CLM download support - brcmfmac: request_firmware_direct is quieter - Sets the BCDC priority to constant 0 - brcmfmac: Disable ARP offloading when promiscuous - brcmfmac: Avoid possible out-of-bounds read - brcmfmac: Delete redundant length check - net: rtl8192cu: Normalize indentation - net: rtl8192cu: Fix implicit fallthrough warnings - Revert "Sets the BCDC priority to constant 0" - media: cxd2880: Bump to match 4.18.y version - media: cxd2880-spi: Bump to match 4.18.y version - Revert "mm: alloc_contig: re-allow CMA to compact FS pages" - Revert "Revert "mm: alloc_contig: re-allow CMA to compact FS pages"" - cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 with MEDIA_SUBDRV_AUTOSELECT - 950-0421-HID-hid-bigbenff-driver-for-BigBen-Interactive-PS3OF.patch - 950-0453-Add-hid-bigbenff-to-list-of-have_special_driver-for-.patch Make I2C built-in instead of modular as in upstream defconfig; also the easiest way to get MFD_ARIZONA enabled, which is required by kmod-sound-soc-rpi-cirrus. Add missing compatible strings from 4.9/960-add-rasbperrypi-compatible.patch, using upstream names for compute modules. Add extra patch to enable the LEDs on lan78xx. Compile-tested: bcm2708, bcm2709, bcm2710 (with CONFIG_ALL_KMODS=y) Runtime-tested: bcm2708, bcm2710 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
6 years ago
From 152d226fd2eff1fdc1f8881287bf1a7d4560b27e Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Mon, 26 Feb 2018 19:46:32 +0000
Subject: [PATCH 233/454] overlays: Rework sdio overlays to allow polling
MMC/SD interfaces support a DT property (non-removable) that disables
the usual polling required to detect card removal for a configuration
that doesn't have hardware card presence detection. This property is
required for the on-board SDIO WiFi interface, but other uses of the
interface may want the polling to be re-enabled.
'non-removable' is a boolean DT property - true if present, false if
absent - and the overlay mechanism does not allow a property in the
base DTB to be deleted, so if the base DTB has non-removable set
(which is true for all WiFi-equipped Pis) then an overlay cannot
unset it.
Modify the SDIO overlays to work around this problem by disabling
the mmc node and adding a clone to which non-removable may
optionally be added.
N.B. The default state of poll_once is still true, and the overlay
does include a non-removable property, but setting poll_once to false
("off") will remove the property from the overlay before it is applied.
See: https://github.com/raspberrypi/linux/issues/2401
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
---
.../boot/dts/overlays/sdio-1bit-overlay.dts | 40 +++++++++++++-----
arch/arm/boot/dts/overlays/sdio-overlay.dts | 41 ++++++++++++++-----
2 files changed, 59 insertions(+), 22 deletions(-)
--- a/arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts
+++ b/arch/arm/boot/dts/overlays/sdio-1bit-overlay.dts
@@ -8,21 +8,39 @@
fragment@0 {
target = <&mmc>;
- sdio_mmc: __overlay__ {
- compatible = "brcm,bcm2835-mmc";
- pinctrl-names = "default";
- pinctrl-0 = <&sdio_pins>;
- non-removable;
- bus-width = <1>;
- brcm,overclock-50 = <0>;
- status = "okay";
+ __overlay__ {
+ status = "disabled";
};
};
fragment@1 {
+ target = <&soc>;
+ __overlay__ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ sdio_1bit: sdio@7e300000 {
+ compatible = "brcm,bcm2835-mmc",
+ "brcm,bcm2835-sdhci";
+ reg = <0x7e300000 0x100>;
+ interrupts = <2 30>;
+ clocks = <&clocks 28/*BCM2835_CLOCK_EMMC*/>;
+ dmas = <&dma 11>;
+ dma-names = "rx-tx";
+ brcm,overclock-50 = <0>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio_1bit_pins>;
+ non-removable;
+ bus-width = <1>;
+ };
+ };
+ };
+
+ fragment@2 {
target = <&gpio>;
__overlay__ {
- sdio_pins: sdio_pins {
+ sdio_1bit_pins: sdio_1bit_pins {
brcm,pins = <22 23 24 25>;
brcm,function = <7>; /* ALT3 = SD1 */
brcm,pull = <0 2 2 2>;
@@ -31,7 +49,7 @@
};
__overrides__ {
- poll_once = <&sdio_mmc>,"non-removable?";
- sdio_overclock = <&sdio_mmc>,"brcm,overclock-50:0";
+ poll_once = <&sdio_1bit>,"non-removable?";
+ sdio_overclock = <&sdio_1bit>,"brcm,overclock-50:0";
};
};
--- a/arch/arm/boot/dts/overlays/sdio-overlay.dts
+++ b/arch/arm/boot/dts/overlays/sdio-overlay.dts
@@ -8,20 +8,39 @@
fragment@0 {
target = <&mmc>;
- sdio_mmc: __overlay__ {
- pinctrl-names = "default";
- pinctrl-0 = <&sdio_pins>;
- non-removable;
- bus-width = <4>;
- brcm,overclock-50 = <0>;
- status = "okay";
+ __overlay__ {
+ status = "disabled";
};
};
fragment@1 {
+ target = <&soc>;
+ __overlay__ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ sdio_ovl: sdio@7e300000 {
+ compatible = "brcm,bcm2835-mmc",
+ "brcm,bcm2835-sdhci";
+ reg = <0x7e300000 0x100>;
+ interrupts = <2 30>;
+ clocks = <&clocks 28/*BCM2835_CLOCK_EMMC*/>;
+ dmas = <&dma 11>;
+ dma-names = "rx-tx";
+ brcm,overclock-50 = <0>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio_ovl_pins>;
+ non-removable;
+ bus-width = <1>;
+ };
+ };
+ };
+
+ fragment@2 {
target = <&gpio>;
__overlay__ {
- sdio_pins: sdio_pins {
+ sdio_ovl_pins: sdio_ovl_pins {
brcm,pins = <22 23 24 25 26 27>;
brcm,function = <7>; /* ALT3 = SD1 */
brcm,pull = <0 2 2 2 2 2>;
@@ -30,8 +49,8 @@
};
__overrides__ {
- poll_once = <&sdio_mmc>,"non-removable?";
- bus_width = <&sdio_mmc>,"bus-width:0";
- sdio_overclock = <&sdio_mmc>,"brcm,overclock-50:0";
+ poll_once = <&sdio_ovl>,"non-removable?";
+ bus_width = <&sdio_ovl>,"bus-width:0";
+ sdio_overclock = <&sdio_ovl>,"brcm,overclock-50:0";
};
};